to follow, share, and participate in this community.
I have a netvanta 3140 with some pretty hefty config. I inherited this, but I think one of my secondary public IPs Subnet is wrong. My main subnet is x.x.x.x 255.255.255.240 mask. All of the secondar... I have a customer who has a Mitel PBX that I am providing a SIP trunk to (I am the Service Provider). He is requesting that we only send refresh messages and not RE-Invites. I am not sure what he's talking... NV3140 being used for a SIP Trunk Issues are intermittent fast busy when calling out, and possibly some incoming calls failing. Secondary issue is the customer is trying to use a fax service across this, which ... Have a 3140 with EFP, not utilizing any SIP functionality on the platform other that QOS for SIP running thru the router. Can SIP ALG be disabled? Can SIP the SIP functionality be disabled globally? ... On a SIP Trunk (using a NV3140) what is the recommendation for setting the transfer, forward, and feature modes? Local or Network? Should this be set globally or within each SIP Trunk (one trunk faces the provi... Has anyone ever setup a netvana 3140 SBC with comcast sip services? They are stating that if we use a netvana, it must emulate a PBX in order for their services to work. Does anyone know what they are talking about? Hi there, I'm hoping this is a simple(r) question. We are a small tech support company, and are pretty technically proficient, but we are normally dealing with routers such as barracuda/sonicwall/ubiquity. A p... I'm trying to figure out what kind of throughput I am going to get with a 3140. The firewall will be disabled and there are no VPNs, but it will be doing QoS. Can I expect higher than the 600Mbps on the product matrix... I have setup WAN fail-over on NV3120. The primary is Comcast and backup WAN is FIOS. The fail-over works and when Comcast goes down it fails to FIOS as expected. But the problem is when Comcast link comes back... I have an Adtran 3140 (PN 1700341F1) and need to perform a hard reset (cannot log in). There does not appear to be a reset button. Are there any alternatives? I have a NetVanta 3140 (ver.13.5.1) and I am looking to configure WAN internet fail over between Comcast and FIOS internet link. Comcast interface is on static IP but FIOS interface is on DHCP. Any sample configurat... need to set port forwarding on 3120 Hello, We have two ISP's that we Peer with. Currently we have one 3140 with both ISP's feeding into the router but obviously this creates a single point of failure. Is there any documentation on setting up a 3... Hello. Does the Netvanta 3140 support rfc2833 out-of-band DTMF for SIP Trunking? I have enabled this option many times in Adtran 908 and so forth, but do not see the option in OS R13.2.2. Typically, we use:... Good Day, Checking to see what the minimum version of AOS is required for the 3140 to enable netflow. I'm running R11.10.7.HA, which I think is too old. I found the Excel AOS Feature Matrix for ver... We purchase quite a few 3140's as demarc routers. My suppliers are telling me they are getting difficult to purchase, are they going EOL? If so, what is going to be the alternative is the price points of the 3140? Th... I've got a 3120, and am wanting to know about this Top Traffic tool, and if it's a reliable tool to tell me if I've got devices utilizing a lot of the available bandwidth at a remote site. Out of curiosity, d... i want to know how many concurent call are made on my sip trunk, min / max I have many units setup however due to security needs I have customers wanting ports open only from specific Public IP addresses. How do I accomplish this in the CLI. I am working on putting together a dual WAN, "high availability" topology with a pair of 3140's. This will be to support our hosted IP phones, leveraging the SIP proxy functionality. I am using VRRP on my LAN interfac...
Get a feed of this content