to follow, share, and participate in this community.
I have an application where the public IP address is dynamic, not static. I want gig eth 0/2 for the public Internet. I know that for a static IP you set the default route command 0.0.0.0 0.0.0.0 w.x.y.z (... I want to use Nv 3140 with 2 subnets, one on Gig 0/1, second on Gig 0/3; Internet WAN on Gig 0/2. I connect Gig 0/1 to an unmanaged switch that is not connected to Gig 0/3; connecting a pc with DHCP con... Is there a way in the GUI to set up a device with a reserved IP address? I can't seem to find how to assign static addresses to a specific mac address on a device. Eddie First time setting up one of these and I'm running into an issue where DNS resolution will work for a while, then stop. Router was setup using webui. I think it has something to do with my DHCP pool settin... I have noticed lately my router is not assigning DHCP to some devices. My mac this morning would not draw a DHCP from the router. It auto assigns. I have noticed some of our Mitel VOIP phones if powe... I have a Netvanta 3120 which I'd like to repurpose as a LAN switch. The router in the network is configured with some static LAN addresses and a LAN pool for DHCP leases. The next hop from the router in th... I have a NetVanta 3120 with a Port forward for RDP This works well. I now need to restrict this access to one external IP address for security. I have tried stumbling through a few configs but with no luck...... I have a netvanta 3140 with some pretty hefty config. I inherited this, but I think one of my secondary public IPs Subnet is wrong. My main subnet is x.x.x.x 255.255.255.240 mask. All of the secondar... I have a customer who has a Mitel PBX that I am providing a SIP trunk to (I am the Service Provider). He is requesting that we only send refresh messages and not RE-Invites. I am not sure what he's talking... NV3140 being used for a SIP Trunk Issues are intermittent fast busy when calling out, and possibly some incoming calls failing. Secondary issue is the customer is trying to use a fax service across this, which ... Have a 3140 with EFP, not utilizing any SIP functionality on the platform other that QOS for SIP running thru the router. Can SIP ALG be disabled? Can SIP the SIP functionality be disabled globally? ... On a SIP Trunk (using a NV3140) what is the recommendation for setting the transfer, forward, and feature modes? Local or Network? Should this be set globally or within each SIP Trunk (one trunk faces the provi... Has anyone ever setup a netvana 3140 SBC with comcast sip services? They are stating that if we use a netvana, it must emulate a PBX in order for their services to work. Does anyone know what they are talking about? Hi there, I'm hoping this is a simple(r) question. We are a small tech support company, and are pretty technically proficient, but we are normally dealing with routers such as barracuda/sonicwall/ubiquity. A p... I'm trying to figure out what kind of throughput I am going to get with a 3140. The firewall will be disabled and there are no VPNs, but it will be doing QoS. Can I expect higher than the 600Mbps on the product matrix... I have setup WAN fail-over on NV3120. The primary is Comcast and backup WAN is FIOS. The fail-over works and when Comcast goes down it fails to FIOS as expected. But the problem is when Comcast link comes back... I have an Adtran 3140 (PN 1700341F1) and need to perform a hard reset (cannot log in). There does not appear to be a reset button. Are there any alternatives? I have a NetVanta 3140 (ver.13.5.1) and I am looking to configure WAN internet fail over between Comcast and FIOS internet link. Comcast interface is on static IP but FIOS interface is on DHCP. Any sample configurat... need to set port forwarding on 3120 Hello, We have two ISP's that we Peer with. Currently we have one 3140 with both ISP's feeding into the router but obviously this creates a single point of failure. Is there any documentation on setting up a 3...
Get a feed of this content