• Netvanta 3200 Ethernet as a Trunk Port?

    We have been using the Netvanta 3200 devices to extend our network to remote locations via T-1 interface module.  We have been using the "Transparent" mode to pass everything.  We have recently started incor...
    last modified by rookus
  • When is ncommand going to drop flash requirements?

    This support community is basically a ghost town, so I don't know why I bother, but when is ncommand going to drop flash requirements?
    last modified by jbonner
  • How to configure bridge mode in NetVanta 3200 with 2 T1s

    Adtran Experts. I have the following question and I really need help. We are replacing old firewalls with embedded T1s with new firewalls with no T1s. We have an MPLS circuit with a multilink T1s. Per the vendor, I...
    last modified by pacunetadmin
  • Point to Point configuration for Comcast Cable Help

    So here is my problem.  I can ping from my laptop ( to all the router inter faces in Router 1 & 2 and to the Workstation on the other side (  I can ping from Workstation (172.16.1...
    last modified by hanpaver
  • How do i configure my router to use a point to point connection over comcast cable.

    I am switching from a point to point t1 line and am having trouble with bringing the new Point to point thru Comcast Cable.  What changes are need to be made or do I need a new Router.   Building configurat...
    last modified by hanpaver
  • Activating interfaces

    Preface: I'm not an IT expert   We have an Adtran Netvana 3200 router with a T1 Wan interface.   The T1 interface seemed to be dead, plugging into our Verizon smart jack doesn't affect the status LED's, th...
    last modified by artbev
  • I have (2) Netvanta 3200 routers I want to set up for a point to point T-1.

    One is a Gen 2 and the other is a Gen 3, both have the latest release of software available for them on them, but of course the menus in the GUI are different. They are being used to replace two netopia routers that f...
    last modified by tptech
  • NTP Master

    I have configured a Cisco router as an NTP Master and I have successfully synced multiple Adtrans routers to it for NTP.  When I try to sync a Juniper switch to the Adtran I get no suitable syncrhonization server...
    last modified by redbarron
  • Support Vouchers - what will I get?

    I have to buy support vouchers to get any help with my adtran unit.  What type of help will I actually get from support using the vouchers.  Can they give me command line info to retrieve info and then progr...
    last modified by cmh-tech
  • Can the 3305 do maintain multiple NAT tables?

    I need to NAT two separate Class C nets.. can the 3305 do it..
    last modified by dalfon
  • 3120 has high CPU with FFE enabled and IP firewall disabled

    ADTRAN, Inc. OS version R12.2.0.SA   Mainline Version: ENM.16.93   P4 Changelist: 268653   Checksum: 9C1988B5   Built on: Wed Nov 16 11:29:53 2016 Boot ROM version   Checksum...
    last modified by redbarron
  • Caller ID Restricted

    We have a fractional T1 on all lines but 1 the Caller ID on the outbound calls show RESTRICTED, we have to remove it,   the phone provider says that the setting is in the Channel Bank and they receive it as rest...
    last modified by egc
  • OPERATING_SYSTEM.SMTP Could not connect to email server.

    Hi there I have a Gen 2 3200 - updated to 15.12.00 firmware.   I'm getting this error no matter how I configure Email Forwarding.  We use gmail/g-suite so I've tried the following for servers:   s...
    last modified by olddocx
  • Static Routes on 4430 with VPN not removing Static Routes from Routing Table when BGP Routes return

    I have an Adtran 4430 with many VPN connections going out the WAN interface as backup routes for a lot of the routes that are coming in via EBGP on the LAN interface over a GRE tunnel to our MPLS router.  In norm...
    last modified by redbarron
  • NetVanta 3305 Status light is red

    I have a NetVanta 3305. This morning suddenly our internet was down and the router status light was red. I found that the red light indicates "Power is on but the self-test failed or the boot code could not be loaded....
    last modified by jrookie
  • Secondary IP Address

    How does the "ip address <ip-address> <subnet-mask> secondary" command works? Like what mac-address does it use? Does it create another mac-address or it just uses its interfaces mac-address because I'm ha...
    last modified by dijkstra
  • Netventa 3200 bonded T1's

    I am working with a customer with a Netventa 3200 with 2 bonded T1's point to point to their other location.. When T1 number 1 drops, both circuits drop, ppp1 says starting.  If T1 number 1 is up and T1 number 2 ...
    last modified by jmorris
  • Is it possible to parse output for a specific string?

    When issuing commands that will produce verbose output, does AOS have a filter? Other routers can pipe to find/match/include/exclude, etc.. EDIT: Update. I have 2 adtrans for training. On the 3200 (the one on which ...
    last modified by adtr239
  • using netvanta 3200 for bonded T1 support to the internet

    I have some netvanta 3200's that I would like to configure to support a bonded T1 (two T1's).  I haven't done bonded T1 for more than 10 years (forgot).  can you point me to some documentation how to impleme...
    last modified by larryp
  • Netvanta 3200 | (Interface) Frame Relay, Sub-Relay & Loopback Questions

    Good day...   I am replacing an Samsung IBG-1000 for a customer using an Adtran Netvanta 3200. I have contacted the clients provider (MegaPath | T1) and asked for general support however they do not support the ...
    last modified by wubblegubble