to follow, share, and participate in this community.
I'm pretty new to routing (I usually work on the Firewall side), and I need to do something that seems like it should be easy, I'm just not sure if I have a good understanding of what I'm doing here. My ISP pr... Hi, I've got a VPN tunnels set up between two NV3430 routers, and it works fine for all LAN devices on both sides to see each other. One side has a LAN of 192.168.1.1/24 and a static WAN that's on the In... Hi, We have a NV3450 currently running R10.9.3.E. Looking at getting this firmware upgraded. We have our device registered on MyAdtran, but when we go to download the new firmware it only gives accessibility to the ... I am at bit of a loss with a configuration I have built. The scenario was to create a routed failover configuration. That part works, although the failover part was not been tested but access fo the WAN 2 is confirmed... I'm relatively new to the Adtran world so bare with me if I ask stupid questions. My client wants to set up WAN failover on their Netvanta 3430. I noticed that this model only have Eth 0/1 and Eth 0/2. Eth 0/... I am seeing input and CRC errors on WAN interface at one of branch router. Topology overview is : WAN----> Adtran 3430 (eth 0/1) -------> Juniper 2200 (LAN via eth 0/2). We are using site to site VP... I've searched the forums and have seen the solution is to configure stateless on the ip policy, however when I tried that, the problem became worse than better. I'm assuming I just don't know exactly how to conf... I uploaded a firmware file via the GUI which couldn't be assigned as a primary or secondary firmware boot. I attempted to assign it as a boot file in the GUI and the file didn't show up in the drop down menu. I ... How can you set up port forwarding for pinging a device behind an Adtran router from the outside? Customer needs to ping a device on the network from a remote location. I have two 3448's in two offices. Site A has two internet connections and Site B has one. Both locations have two vlans, one (100) for computers and one (110) for voice. Right now I have a established VPN for the voic... Does the NetVanta 3448 support the Network Monitor feature described in the document Configuring WAN Failover with Network Monitor in AOS? We have a first generation 3430 originally part number 1200820E1 that was upgraded in 2011 to the E2 license (1950820E2 currently running R10.9.1) so that it could provide VPN access. I happened to check out the softw... The first network security scan on our Netvanta 3448 failed the PCI DSS Compliance requirements. Firmware reports version 18.03.01.00, device part number is 1200821E1 and we have about 20 of these devices configured t... Hello, I have a netvanta 3420 router that was already installed in the business I was hired to manage. I need to allow the owner to access the video server through the internet. So he may log in and watch ever... How to configure Netvanta 3448 to work with CenturyLink PPPoE ? Tried both authentication types "PAP and CHAP" neither works and then there are a lot of other check boxes plus Peer Authentication which I don't know wh... 1 - When upgrading my 3120's to the latest firmware, most are requiring a boot rom upgrade first. Is there a similar requirement on the 3448's? Currently at 11.10.1E - upgrading to 13.2.2E. 2 - I ch... I am trying to configure a Netvanta 3448 to give dhcp addresses out and have them route back to a internet connection i am getting from my ISP. below is my current config. The problem is when connectin... I've got VLANs working on my internet network, with VLAN1 untagged (native), and a few others tagged. Most of my infrastructure is Cisco SG300 and SG500 switches. I've currently got my NV3430 working using... We're having a strange issue with a particular dual wan configuration. This is using a NetVanta 3448. It's running NV3448A-R12-3-3.biz firmware. We two WAN circuits, an ethernet over fiber link (primary) and a... I am using a Netvanta 3448 on Firmware R12.3.3.E. Is there any way to allow a group of IPs through Port Forwards that are translated to user-specified ports? I know you can go through and add every al...
Get a feed of this content