to follow, share, and participate in this community.
Hi Team, i have a setup below: Mitel PBX<----->SIP Trunk<----->(LAN)Adtran908e(WAN)<----->SIP Trunk<---->Third Party SIP Service Provider. i am sending Fax over T38 from our PBX to Th... Hi Team, we have below setup: PBX<--->SIP Trunk<--->(LAN)Adtran(WAN)<-->SIP Trunk<-->SIP Service Provider(Third Party). when i am sending Invite to Adtran, it is not forwarding... Hi, I am using Adtran as a gateway to our PBX. When I am making any calls from PBX, Adtran 908e is not forwarding the Invite to the far end. I am getting 403 from Adtran. Looks like I am making mistake in Perm... Hi Guys, I am dialing a PSTN phone from our IP-PBX through FXO port of Adtran. Even though I am cancelling the call, PBX is not able to send CANCEL. Because according to the sip signalling call had alrea... Get a 503 back when making inbound call to SIP Trunk on (Adtran 924e) ----------------------------------------------------------------------------------------------- N2P-TA924#debug sip stack mes sum N2P-TA924#debu... Hi, When I make any outbound call from our IP-PBX to Adtran, Adtran is sending 400 bad request as response. There is no reason in the wireshark trace as to why Adtran is sending 400 bad request. The interestin... We have been using ADTRAN 908e as an outbound Proxy and the expectation is to convert UDP to TCP for all SIP messages. Can someone please confirm whether Adtran supports it or not? We have been seeing 403 Forbidden f... Product: Adtran 924eG3 w/LFXO Firmware: ADTRAN, Inc. OS version R12.2.0.SA.E Running into an issue where the phones behind the Transparent SIP Proxy are refusing to register correctly. If the phone is connect... Customer has a gig internet connection and wants the 4430 as the firewall for everything. Adtran 908e (esbc enabled) sits behind it with a private IP. 908 is SIP to PRI for a PBX. I have the 4430 sending all traffic f... Hello, I have an Adtran 908e 3rd Gen that I have a SIP transparent proxy setup on. Everything seems to be working correctly, only I can not seem to set the server registration refresh rate. I have the... Would it be possible to set up site to site extension dialing in the following scenario? In a private MPLS network, where Site A can ping Site B: Site A has a Netvanta 7100 that has SIP coming in from the carrier..... voice trunk T02 type sip description "SIP Trunk 2 to Broadsoft through SBC" sip-server primary sbc.example.com registrar primary sbc.example.com registrar threshold absolute 30 ... Apparently the Taqua T7000 does not recognize * codes on a sip trunk from a sip endpoint. I am using a 908e 3rd gen to provide fxs trunks here in our office. I would like to call forward 1 of those fxs (wh... I have a customer that wants to use 24 analog devices with my company's hosted IP PBX. We do not support SIP trunks and require devices to register as an endpoint. Can the 924 register each FXS port as if it were an i... I need some advice for Toll Fraud Prevention over PRI. We have an Asterisk PBX connecting over a PRI on a TA908. The customer is a repeat Toll Fraud Victim, their PBX spans several offices over a la... We recently attempted to configure an ADTRAN TA908e to be a SIP proxy for our Metaswitch in order to use for SIP failover over a PRI. We had tested this in the lab and have deployed at a separate customer site w... Hello, I have a question on SIP proxy. Do I have to use the Adtran unit as the DHCP server? Reason I ask is I tested SIP proxy successfully on a 908e with internal DHCP server and now I am testing it on a 924e with ex... Hello, I am setting up transparent proxy on an Adtran 908e. I can't seem to get my phones to register and in the debug I am seeing the following error: SIP.PROXY ROUTING No route available for destination x.x.... Hello, I have a FXO line that is being routed to a SIP Trunk. I want to have the 900E only use the local ring-group if the SIP trunk is down. Is there any way to do this? Hi, Need to find out what AOS version an ADTRAN 908E needs to be running for SBC feature package.
Get a feed of this content