• How to have FXS voice users (fax) use different SIP Server than the ISDN PRI port, or should we do NAT instead?

    Hello,   We currently have a TA908e that has an active ISDN PRI running, but we need to add fax lines currently on another ATA to it. We need to either: 1. Add voice users for the FXS ports, but they have to us...
    sharpy
    created by sharpy
  • Total Access 908e (3rd Gen) P/N: 4243908F1 Firmware

    We have been looking at upgrading the firmware for Total Access 908e (3rd Gen) P/N: 4243908F1. I don't see a link to download 908e firmware but i can download 900e software.   Does the same firmware work for 908...
    vuppandm
    last modified by vuppandm
  • cannot route to interface of 908e across SDWAN

    interface eth 0/1   description Outside   ip address  1x2.1x6.xxx.xx  255.255.255.248   ip mtu 1500   media-gateway ip primary   traffic-shape rate 1000000   max-reserved-bandwi...
    avayaguy
    last modified by avayaguy
  • SIP-PRI plus FXS lines on Metaswitch

    I can get a authenticated SIP binding to run a PRI and that works great (basic config below) I can get a SIP trunk (no binding) to allow the FXS lines to individually register (basic config below)   but----the ...
    dealy
    last modified by dealy
  • TA9XX MGCP replying to AUEP & RQNT from a switch that's not configured in the TA

    Presently using a Metaswitch 3510, converting to a RedCom HDX.  Problem is that my TA9XX units are replying to the HDX messages and registering to the new switch even though nothing about the HDX or subnet is not...
    spanky216
    last modified by spanky216
  • TA924 to Asterisk SIP?

    This should seem straightforward, but I cannot get outcalling from my TA924 FXS ports through my Asterisk to work. Inbound calling through the Asterisk to these FXS ports works just fine. But when I grab a line from o...
    gregarican
    last modified by gregarican
  • Can you retrieve the BootROM version via SNMP or Autolink?

    I want to upgrade all of my AOS devices to R13.6.0, and I want to verify the BootROM version is at the minimum level, however I don't want to long in individually and enter the show version command.    ...
    timlytle
    created by timlytle
  • Removing an Extended IP access list Total Access 908e

    I am trying to figure out how to remove this entry that I did by mistake using the CLI   Extended IP access list web-acl-6      permit ip any any log   Thanks Chris
    ventura
    last modified by ventura
  • Looking for TA sample configuration script with redundant wan route with SBC ip change.

    Hi,   Exploring possible SBC solutions.  We have a customer that has a direct T1 SIP and a cable internet connection.  I'm looking to understand how something like a TA 908e with SBC (or current device...
    keith
    last modified by keith
  • Call Block

    Is there a way to block numbers in the Total Access 908?
    kurttsc
    last modified by kurttsc
  • Has anyone been able to trunk together 2 TA908e devices?

    We have two TA908e with amphenol cable connnections and we would like to have one where the PRI comes in and it'll hand off over a trunk to the other adtran if the main one does not have the extension.   example...
    jadams1227
    last modified by jadams1227
  • URI is not correct in SIP invite

    First time setting up a 908e to use FQDN instead of IP addresses to SIP provider. I have my SIP trunk registered and can receive inbound calls but unable to make outbound calls. Did a trace with the provider and they ...
    jeremy.f
    last modified by jeremy.f
  • How to configure 908E for PRI to KTS for a new phone system ?

    We are wanting to setup a 908E to use it as a gateway to a new KTS system. We are replacing an existing phone system which is now using PRI so we would like to emulate this setup in our lab so the cutover transition w...
    rneidlinger
    last modified by rneidlinger
  • TA908e PRI to SIP can't dial out (New install)

    I am trying to install an Adtran TA 908e for the first time to provide PRI service into a Mitel 5000 PBX from Broadsoft SIP trunking service, we have inbound service working fine but calling out from the Mitel always ...
    acejavelin
    last modified by acejavelin
  • Trunk Calls from Adtran TA 908

    Hello,   I have a customer that is reporting errant calls from the trunk side of their phone system, and an Adtran 908 2nd Gen is being used as their SIP to PRI. I don't see anything from the Adtran side that wo...
    cwqwest
    last modified by cwqwest
  • What does RTP PACKET DELAY do and mean?

    Having issues wit ha 924e with sip in pots out when a modem call comes in we can download 75% of the file then the call drops. Can this be fixed by  RTP PACKET DELAY commands?
    biohazmat
    last modified by biohazmat
  • Adtran 924E behind router/firewall

    i have a situation where i need 60 FXS ports to connect to my SIP server each fxs port  shuold connect with a unique sip user/password   now i dont have enough Public IP address for all the adtran devices, ...
    mtghr
    last modified by mtghr
  • Adtran TA908e 3rd Gen T.38 on PRI

    I see that the newer Adtran TA908e 3rd Gen supports up to 30 T.38 sessions. Can T.38 be enabled on the PRI interface or is it just available for the FXS ports?
    cwallace
    last modified by cwallace
  • Having trouble with dial plan on 900e

    The setup has the fxs port registered as sip endpoint. When I make calls that match the default dial plan the call cuts through immediately. If I try to make a call that requires a star code first there is about a fou...
    tech706
    last modified by tech706
  • Getting this when setting up a FXS to SIP trunk call: Looking up source address for destination x.x.x.x. Delivering ERROR: unable to get local address

    Here is the debug: Looking up source address for destination 192.168.107.12 14:03:18.371 PM.0:9 Idle                 Processed OFFHOOK ...
    wernerg
    last modified by wernerg