I have had more than one Bluesocket ExpressCloud network start displaying the following error on devices after the 3.3.0-656804 update. The WiFi network "SSID" does not appear to be connected to the internet. ... BSAP 3.2.0-HC has been released to hotfix a reboot associated with Dynamic Multicast Operation. You can avoid this reboot by updating your AP firmware to 3.2.0-HC. 3.2.0-HC firmware should only be used with 3.2.0-X vW... We've got our vWLAN logging to Splunk, however the time stamps are all off 4 hours. It appears that even though we're set for NTP, the syslog facility is not using the local time in the timestamp. This is ... So, I've just managed to get my hands on 5 BSAP-1800c's and a BSAP-1840c. How do i go about registering the BSAP-1800C's? The 1840 registered without any problems through the website licensing portal but the serial nu... Does the TA900e (3rd Gen) support 4 wire T1s facing the customer's PBX? We have a customer with an old PBX that requires a 4 wire T1 for their voice and I can't find any documentation that says anyth... NV3140 being used for a SIP Trunk Issues are intermittent fast busy when calling out, and possibly some incoming calls failing. Secondary issue is the customer is trying to use a fax service across this, which ... 19:24:07.863 ISDN.L2_FMT PRI 1 R Sapi:00 C/R:R Tei:00 INFO Ns:81 Nr:70 P:0 19:24:07.863 ISDN.L2_FMT PRI 1 Prot:08 CRL:2 CRV:0008 19:24:07.863 ISDN.L2_FMT PRI 1 ... Hello, How is http enabled on the NV6360. I'm running the default config and the http command does not work. NetVanta 6360 Default Configuration Thank you I'm preparing to install the device between the carrier and the customer's PBX. Currently two PRI circuits connect to their PBX directly. Both PRI circuits have a D-channel (FAS) and they're provisioned as one logical... Looking for the best solution router that will avoid/eliminate packet collisions or allow packet flow even if shaping is in place from the LEC . We have procured a remanufactured TA 600RT1 TDM, 3rd GEN (4203600L1#TDM). s/n HDCDENAN4213680L1 for my small business. We have a verizon T1 just installed. I spoke to ADTRAN via Caes #4993148 and tec... Adtran 1550 Syslog is missing after reboot. I need to prevent this. I also need to know how to extend the buffer of the syslog as its crazy short right now. i have a device that i can not connect via SSH i reviewed the config a few times and it looks ok i am posting the config here maybe someone might catch whats wrong . ! !... I was in the process of migrating all connections from a 24 port Adtran Netvanta 1200 series switch over to a Netvanta 1238 48-Port switch, but once I filled up the 1st 24 ports, the other half of the switch was not w... Admittedly, I'm going in to this configuration completely blind. I have plenty of networking experience, but telephony, T1 lines, DSX, channel banks, etc is a whole different world to me. So, this might be more of a... On a SIP Trunk (using a NV3140) what is the recommendation for setting the transfer, forward, and feature modes? Local or Network? Should this be set globally or within each SIP Trunk (one trunk faces the provi... Hi, Currently dealing with 3x BSAP2020s and trying to get them to connect either with my on-prem vWLAN server or Express Cloud. These APs have been repurposed and the SSH information is unknown, I was curious ... We have a customer that wants to keep the originating caller ID when transferring inbound calls outside the PRI? Is there a link to default configurations that come on CPE? More specifically the 1550-24P.