Hello, I would like to to use an Adtran 908E as the gateway device so that I can peel off a few analog lines as well. This is my first experience with Adtran and its going pretty well, but I am unable to get outbound... Hello friends, I spent so much time and still cannot figure out how to insert a caller id override for all FXS analog stations on the Adtran TA924e. We have multiple FXS analog stations to be able to call out... We are trying to configure a TA924e to connect to a SIP trunk provider SIPStation through internet connection so it can provide a few analog lines (trunk lines) for our legacy PBX (Mitel). We specifically want to ha... We purchase quite a few 3140's as demarc routers. My suppliers are telling me they are getting difficult to purchase, are they going EOL? If so, what is going to be the alternative is the price points of the 3140? Th... I have an IPFlex from AT&T which is currently plugged into an NEC SV8100. That all works, but I'm trying to put an AdTran 908e in so I can phase out the SV8100 and transition over to a FusionPBX system. ... This document explains how to configure IPv4 Dynamic Host Configuration Protocol (DHCP) server IP address pools using the web-based Graphical User Interface (GUI) and the Command Line Interface (CLI). The examples use... In the configuration on a 900e 3rd Gen, what is the difference between Network and User settings on PRI interface settings? What setup differences are they each portraying? I would assume as the PRI goes to PBX it wou... I have a 7100 that has been configured for several years using analog lines and a scheduled system mode change to send calls to specific Auto Attendants based on the time of day. I am attempting to establish a n... I've got a 3120, and am wanting to know about this Top Traffic tool, and if it's a reliable tool to tell me if I've got devices utilizing a lot of the available bandwidth at a remote site. Out of curiosity, d... I am trying to override the Callerid for only calls originating from the PRI and Not from the fxs/voice ports Is this possible ? We are in progress on replacing our Netvanta 1238 and 1324's with Cisco SG350-52MPs. Our Netvanta 1544's will eventually be replaced with some model of Catalyst (I'm just uncertain of the model). Right now we ... Hi Support, I would like to implement a similar solution as depicted in the below diagram (Adtran's sample network). This would be my final configuration setup. However, before I reach this a... Hi, we having a issue with user number substitution. We using a extension like 2911 for service call. Those call in night mode are redirect to a external partner whos answer the emergency call. The problem is even if... The physical interface supports Jumbo Frames: config-giga-eth 0/2)#mtu <60-9242> - MTU (bytes) But it looks like the IP int... BSAP 3.2.0-HC has been released to hotfix a reboot associated with Dynamic Multicast Operation. You can avoid this reboot by updating your AP firmware to 3.2.0-HC. 3.2.0-HC firmware should only be used with 3.2.0-X vW... i want to know how many concurent call are made on my sip trunk, min / max Whether I attempt to go in with HTTP or HTTPS with the default admin/password credentials the login box does not accept my entry. On the 3rd attempt/failure it says not authorized. Telnet accepts my "adtra... Question: How do you send debug output to a Syslog Server from an AOS device? Answer: The ability for AOS devices to send debug output to a Syslog Server was added in AOS release R13.2.0. You will need a... Our phone system is in an active/passive setup and when we flip between them they send a SIP Re-Invite with a replaces option to the Adtran so that the new active server can take over the call. When we send this to ou... I have many units setup however due to security needs I have customers wanting ports open only from specific Public IP addresses. How do I accomplish this in the CLI.