• RTP Packet Loss

    Hello, in need of some assistance. I have a TA900 providing trunks to Asterisks box. After a power outage all my calls are horrible. Monitoring the calls from the TA I am seeing heavy RTP packet loss on eth 0/2(LAN). ...
    g-man
    last modified by g-man
  • SB.CALL 3 RTP resource unavailable or SDP negotiation failed. Call from

    I am trying to pass calls between Provider and PBX via TA908. I have eth0/1 as public and eth0/2 as LAN. I can make outbound calls however when an inbound call arrives I am getting an error SB.CALL 3 RTP resource unav...
    g-man
    last modified by g-man
  • PRI will not stay up

    New AT&T IP flex PRI handoff to Adtran TA 908e 3rd GEN will not stay up. D channel is flapping and B channels go OOS and then back in.   It's a partial PRI 10 B channels and D channel 24. I've reviewed confi...
    telnet_jonanderson
    last modified by telnet_jonanderson
  • cannot route to interface of 908e across SDWAN

    interface eth 0/1   description Outside   ip address  1x2.1x6.xxx.xx  255.255.255.248   ip mtu 1500   media-gateway ip primary   traffic-shape rate 1000000   max-reserved-bandwi...
    avayaguy
    last modified by avayaguy
  • Fans Stalling/Resuming on Adtran 5660

    Hello,   We have an Adtran 5660 and we occasionally get emails indicating that a fan has stalled but then resumed. The stall and then the subsequent email that the fan has resume is almost instant.   Anyt...
    poolet08
    last modified by poolet08
  • Netvanta 3430 Internet Speed 30% of Expected Bandwidth  [Solved]

    Good Evening,   We have an old Netvanta 3430 which is connected to our Cox Business Internet.  Our contracted speed is 100M download and 20M upload.  When I connect directly to the cable modem, the spe...
    itcaadmin
    last modified by itcaadmin
  • change sip trunk source port ?

    is there a way to change the contact port for a sip trunk I have an instance where ONE trunk is accepting calls for either of the defined trunks     eg a call routed to sip T02  is going to sip T01 T...
    capepete
    created by capepete
  • DHCP on Netvanta 3140

    Is there a way in the GUI to set up a device with a reserved IP address? I can't seem to find how to assign static addresses to a specific mac address on a device.   Eddie
    ecarter
    last modified by ecarter
  • I have serious issues with Netvanta 1550-48P working with Hikvision IP Cameras.

    It takes forever for the switch to establish a connection with a camera. Lights blink orange/green and go off. All those cameras worked perfectly fine on Cisco switch for years. Eventually they may or may not come up ...
    radeckd
    last modified by radeckd
  • Netvanta 4305 Bridging Operation/IP address for eth int

    I have a private network consisting of a 4304 at the core, wide octal T1 with Netvanta 1224R at each remote.  I have this configuration running in bridged mode just fine, ppp cross-connected to the T1's etc. ...
    rjbart
    last modified by rjbart
  • bgp route failed to redist to ospf issues..

    AOS should be able to support bgp->ospf redistribution but I cannot get it going for some reason. As you can see below, 169.1.11.0 is on OSPF database but no go to form the OSPF route. Did I miss any?   ...
    cctsay
    last modified by cctsay
  • TA924 (1st Gen) losing web interface?

    I have deployed a refurb Total Access 924 (1st Generation) for breaking out analog phone lines for our IP-PBX. I monitor its SMTP stats with PRTG. And see that this unit seems to lose it's web interface every so often...
    gregarican
    last modified by gregarican
  • Use Hook Flash on Atlas 550 FXS-8

    I have an Atlas 550 and would like to use hook flash to transfer a call. Here is the scenario in which I hope to create. Call is inbound to Atlas on Network Term PRI  NET-1 and ANI routed to a FXS-8 port. That ca...
    hes
    last modified by hes
  • Fiber Jumper Cable MTP to 4 LC/UPC (61445003F1-13)

    richardh.
    last modified by richardh.
  • Atlas 550 interfacing Central Station receiver to a PRI

    We have an Atlas 550 connected to a PRI for our security and fire alarm communications. The Atlass has Analog ports installed and plugs in to our DSC System III receiver. We are using 9 analog ports. My question is wh...
    jerryv
    last modified by jerryv
  • FXS-8 2 disable port

    Hi, having an FXS-8 card into my Atlas 550. the port 7 and 8 are showing disable... all other 6 port are working fine.   the port has been added correctly to the dial plan.   there is a way to reset thos...
    lparent
    last modified by lparent
  • 1531p / 1534p Ping issue

    I have a question and could really use some suggestions and or ideas.   My scenario is that I have 2 Adtran 1531p's 8 port and also 1 1534p 24 port ping issue.   Now, I have switch #1 it's an Adtran 1531p ...
    dw!
    last modified by dw!
  • How to have FXS voice users (fax) use different SIP Server than the ISDN PRI port, or should we do NAT instead?

    Hello,   We currently have a TA908e that has an active ISDN PRI running, but we need to add fax lines currently on another ATA to it. We need to either: 1. Add voice users for the FXS ports, but they have to us...
    sharpy
    last modified by sharpy
  • Bluesocket BSAP 1925 bandwidth issue

    have 24 installed in a complex wired to a Adtran 1544 switch and all connected at 1gb. The site is at 745 mbps both directions. When I 1st connected then we had a speed on 150 mbps down and 135 mbps up. Three days la...
    gnicklaw
    last modified by gnicklaw
  • USB port on a BSAP-2035

    What is the USB port on a BSAP-2035 used for?  There is no mention of it in any documention.   Also, should a "standard" Cisco serial RJ-45/DB9 cable (i.e like is included with every Cisco switch and ...
    edm10
    last modified by edm10