cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Anonymous
Not applicable

Using TA908 as a PRI tester

Jump to solution

I have a few PRI PBX interrface cards I would like to test and see if they work using a TA908e, How can I configure the TA908e to send a call from FXS0/1 out T1 0/3?

Thank you

0 Kudos
1 Solution

Accepted Solutions
jayh
Honored Contributor
Honored Contributor

Re: Using TA908 as a PRI tester

Jump to solution

in4ni wrote:



Here is my config and thank you for you taking the time




!
interface pri 1
  description pri 1
  isdn name-delivery setup
  connect t1 0/4 tdm-group 1
  digits-transferred 7
  role network b-channel-restarts disable
  no shutdown


On one (but not both) of the units modify PRI 1 as follows:

interface pri 1

  ....

  role user

  no shutdown


This will be the one acting like PBX.  The other will be acting like a carrier but it really doesn't matter.

Also on one of the units enter:

timing-source internal

(this is default and won't show in the configuration)

On the other enter

timing-source T1 0/4

It doesn't matter which one is which.

You've got digits-transferred 7 but you've got 3-digit extensions.  This might cause some dialplan issues. Try digits-transferred 3 or configure your users with 7-digit numbers.  ISDN and voice debugs will help once you get the units up and in sync.

By the way, good for you!  A lab environment is the place to test and learn, not a customer's phone closet with your cell battery about do die while on hold to Adtran support.

View solution in original post

0 Kudos
9 Replies
jayh
Honored Contributor
Honored Contributor

Re: Using TA908 as a PRI tester

Jump to solution

Create a PRI interface on the T1, there is lots of documentation on this. Add it to a trunk, and the trunk to a grouped-trunk with some dialed digit pattern.

Connect a phone to FXS 0/1 and dial a pattern matching that of the grouped-trunk.  You can assign a voice user to the FXS port and ring the analog phone from the PBX too.

Standard debugs that will help

  debug isdn l2-formatted

  debug voice verbose

If you have several cards, you can connect two of them to T1 0/3 and T1 0/4 and place calls between them as well.

Anonymous
Not applicable

Re: Using TA908 as a PRI tester

Jump to solution

Thank you for the speedy reply however my config did not work, I was not sure if the problem is with my PBX or interface card so i configured a second TA908 just like the 1st and I am trying to complete a call from FXS 0/1 from TA908-A to FXS 0/1 on TA908-B using a T1 cross-over cable Whewn I place a call from A to B the Voice Verbose shows a "Class of Service error" and Voice debug on TA908-B shows nothing. Please take a look at my config and let me know what to do

Thank you

!
!
! ADTRAN, Inc. OS version A5.02.00.E
! Boot ROM version 14.05.00.SA
! Platform: Total Access 908e (2nd Gen),
!
!
hostname "TA908e"
enable password password
!
clock timezone -5-Eastern-Time
!
ip subnet-zero
ip classless
ip routing
!
!
ip domain-proxy
!
!
no auto-config
!
event-history on
no logging forwarding
no logging email
!
no service password-encryption
!
username "admin" password "password"
!
banner motd #

 
#
!
!
no ip firewall alg msn
no ip firewall alg mszone
no ip firewall alg h323
!
!
!
!
!
no dot11ap access-point-control
!
!
!
interface eth 0/1
  ip address  192.168.2.13  255.255.255.0
  no shutdown
!
!
interface eth 0/2
  no ip address
  shutdown
!
!
!
interface t1 0/1
  shutdown
!
interface t1 0/2
  shutdown
!
interface t1 0/3
  tdm-group 1 timeslots 1,24 speed 64
  no shutdown
!
interface t1 0/4
  shutdown
!
!
interface pri 1
  description pri 1
  connect t1 0/3 tdm-group 1
  role network b-channel-restarts disable
  no shutdown
!
!
interface fxs 0/1
  no shutdown
!
interface fxs 0/2
  no shutdown
!
interface fxs 0/3
  no shutdown
!
interface fxs 0/4
  no shutdown
!
interface fxs 0/5
  no shutdown
!
interface fxs 0/6
  no shutdown
!
interface fxs 0/7
  no shutdown
!
interface fxs 0/8
  no shutdown
!
!
interface fxo 0/0
  no shutdown
!
!
isdn-group 1
  connect pri 1
!!
!
!
no ip tftp server
no ip tftp server overwrite
ip http server
ip http secure-server
no ip snmp agent
no ip ftp server
no ip scp server
no ip sntp server
!
!
ip sip
ip sip udp 5060
no ip sip tcp
!
!
!
voice feature-mode network
voice forward-mode network
!
!
!!
voice trunk T01 type isdn
  description "PRIA"
  resource-selection circular descending
  connect isdn-group 1
  early-cut-through
  alc
  plc
  rtp delay-mode adaptive
!
!
voice grouped-trunk GROUP1
  trunk T01
!
!
voice user 200
  connect fxs 0/1
  password "1234"
  sip-authentication password "1234"
!
!
!
!
line con 0
  no login
!
line telnet 0 4
  login
  password password
  no shutdown
line ssh 0 4
  login local-userlist
  no shutdown
!

!
!
end



Anonymous
Not applicable

Re: Using TA908 as a PRI tester

Jump to solution

After adding a calling plan i get this:   " Deliver event rejected, no trunk appearances available"

20:24:35.602 SB.CCM  :  Org TID = Fxs   Dst TID =

20:24:35.602 SB.CCM isMappable: Call Connection Type is TDM_TO_TDM

20:24:35.602 SB.CALL 13 Idle                 Call sent from 200 to T01 (300)

20:24:35.603 SB.CALL 13 State change      >> Idle->Delivering

20:24:35.603 SA.200 Ca:0 CallPending          rcvd: callResponse from SB

20:24:35.603 SA.200 Ca:0 CallPending          State change      >> CallPending->Calling (CAS_Active)

20:24:35.603 TA.T01 Deliver event rejected, no trunk appearances available

20:24:35.603 SB.CALL 13 Delivering           Called the clearCall routine from Delivering

20:24:35.604 SB.CALL 13 Delivering           SIP Proxy rejected call to 300 for survivability - no matching Proxy user

20:24:35.604 SB.CALL 13 Delivering           No available resources on call from 200 to T01 (last attempt)

20:24:35.604 SB.CALL 13 State change      >> Delivering->Clearing

20:24:35.604 SA.200 Ca:0 Calling              rcvd: clearCall from SB

20:24:35.604 SA.200 Ca:0 Calling              sent: clearResponse(pass) to SB

20:24:35.604 SA.200 Ca:0 Calling              State change      >> Calling->Idle (CAS_Idle)

20:24:35.605 SA.200 Ca:0 Idle                 sent: AcctPhoneMgr_cachg(CAS_Idle) to PM

20:24:35.605 PM.0:1 Call Pending         Pri CA, Idle response, App OFF sent

20:24:35.605 PM.0:1 State change      >> Call Pending->Clearing Fast Busy

20:24:35.606 SB.CALL 13 Clearing             Called the clearResponse routine

20:24:35.606 SB.CALL 13 State change      >> Clearing->CallIdlePending

20:24:35.606 SB.CCM release:

20:24:35.606 SB.CCM  :  Call Struct 0x3f65010 :   Call-ID = 13

20:24:35.606 SB.CCM  :  Org Acct = 200    Dst Acct = T01

jayh
Honored Contributor
Honored Contributor

Re: Using TA908 as a PRI tester

Jump to solution

in4ni wrote:



Thank you for the speedy reply however my config did not work, I was not sure if the problem is with my PBX or interface card so i configured a second TA908 just like the 1st and I am trying to complete a call from FXS 0/1 from TA908-A to FXS 0/1 on TA908-B using a T1 cross-over cable Whewn I place a call from A to B the Voice Verbose shows a "Class of Service error" and Voice debug on TA908-B shows nothing. Please take a look at my config and let me know what to do



[snip]



voice grouped-trunk GROUP1
  trunk T01



At this point in the configuration, add the dial pattern you want to present to the PRI.

For example if you are going to send extensions 300 through 399, enter:

config t

voice grouped-trunk GROUP1

accept 3XX cost 0

Now if you call 300 from the FXS phone you should see it presented to the PRI.

jayh
Honored Contributor
Honored Contributor

Re: Using TA908 as a PRI tester

Jump to solution

in4ni wrote:



After adding a calling plan i get this:   " Deliver event rejected, no trunk appearances available"



20:24:35.602 SB.CCM  :  Org TID = Fxs   Dst TID =


20:24:35.602 SB.CCM isMappable: Call Connection Type is TDM_TO_TDM


20:24:35.602 SB.CALL 13 Idle                 Call sent from 200 to T01 (300)


20:24:35.603 SB.CALL 13 State change      >> Idle->Delivering


20:24:35.603 SA.200 Ca:0 CallPending          rcvd: callResponse from SB


20:24:35.603 SA.200 Ca:0 CallPending          State change      >> CallPending->Calling (CAS_Active)


20:24:35.603 TA.T01 Deliver event rejected, no trunk appearances available


20:24:35.603 SB.CALL 13 Delivering           Called the clearCall routine from Delivering


20:24:35.604 SB.CALL 13 Delivering           SIP Proxy rejected call to 300 for survivability - no matching Proxy user


20:24:35.604 SB.CALL 13 Delivering           No available resources on call from 200 to T01 (last attempt)


Hmmm...  Is the PRI up?

What do you get with

show interface t1 0/3

show interface pri 1


if show interface t1 0/3 is down, you have a physical problem with the T1, you may need a T1 crossover cable.


If show interface pri 1 doesn't look like

.......................D

then you have a problem with the PRI setup, could be the PBX or configuration mismatch.

If both of those are good, then do debug isdn l2-f and post the results.

jayh
Honored Contributor
Honored Contributor

Re: Using TA908 as a PRI tester

Jump to solution

I just spotted something that could be an issue, kind of subtle.



!
interface t1 0/3
  tdm-group 1 timeslots 1,24 speed 64
  no shutdown


This will only allow timeslots 1 and 24, so one bearer channel plus the driver.  Probably not what you want.

Try tdm-group 1 timeslots 1-24 speed 64 instead.

Anonymous
Not applicable

Re: Using TA908 as a PRI tester

Jump to solution

Thank you very much for your replies, I actually had it working for a short wile, however i didnt save my config and now it not working

im trying to attach 2 908's together using a PRI cross over cable, I want to call FXS station on each 908

Currently I am getting a D channel down error ,   Show interface shows PRI 1 as down,

Here is my config and thank you for you taking the time

!
hostname "TA908e"
enable password pass
!
!
ip subnet-zero
ip classless
ip routing
!
!
ip domain-proxy
!
!
no auto-config
!
event-history on
no logging forwarding
no logging email
!
no service password-encryption
!
username "admin" password "pass"
!
banner motd #

        Important

Web username/password is configured to admin/password.

Enable and Telnet passwords are configured to "password".

Please change them immediately.

The ethernet 0/1 interface is enabled with an address of 10.10.10.1

Telnet/SSH access is also enabled.

#
!
!
no ip firewall alg msn
no ip firewall alg mszone
no ip firewall alg h323
!
!
!
!
!
no dot11ap access-point-control
!
!
!
!
!
!
!
!
!
!
!
!
!
interface eth 0/1
  ip address  192.168.2.12  255.255.255.0
  no shutdown
!
!
interface eth 0/2
  no ip address
  shutdown
!
!
!
!
interface t1 0/1
  shutdown
!
interface t1 0/2
  shutdown
!
interface t1 0/3
  shutdown
!
interface t1 0/4
  tdm-group 1 timeslots 1-24 speed 64
  no shutdown
!
!
interface pri 1
  description pri 1
  isdn name-delivery setup
  connect t1 0/4 tdm-group 1
  digits-transferred 7
  role network b-channel-restarts disable
  no shutdown
!
!
interface fxs 0/1
  no shutdown
!
interface fxs 0/2
  no shutdown
!
interface fxs 0/3
  no shutdown
!
interface fxs 0/4
  no shutdown
!
interface fxs 0/5
  no shutdown
!
interface fxs 0/6
  no shutdown
!
interface fxs 0/7
  no shutdown
!
interface fxs 0/8
  no shutdown
!
!
interface fxo 0/0
  no shutdown
!
!
isdn-group 1
!
!
!
!
!
!
!
!
!
!
no ip tftp server
no ip tftp server overwrite
ip http server
ip http secure-server
no ip snmp agent
no ip ftp server
no ip scp server
no ip sntp server
!
!
!
!
!
!
ip sip
ip sip udp 5060
no ip sip tcp
!
!
!
voice feature-mode network
voice forward-mode network
!
!
!
!
!
!
!
voice dial-plan 1 extensions XXX
!
!
!
!
voice codec-list trunk
  codec g729
  codec g711ulaw
!
!
!
voice trunk T01 type isdn
  description "pri2pbx"
  resource-selection circular descending
  connect isdn-group 1
  early-cut-through
  rtp delay-mode adaptive
  codec-group trunk
!
!
voice grouped-trunk PRI2PBX
  trunk T01
  accept XXX cost 0
!
!
voice user 200
  connect fxs 0/1
  password "1234"
  sip-authentication password "1234"
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
line con 0
  no login
!
line telnet 0 4
  login
  password pass
  no shutdown
line ssh 0 4
  login local-userlist
  no shutdown
!
!
!
!
!
end
TA908e#

jayh
Honored Contributor
Honored Contributor

Re: Using TA908 as a PRI tester

Jump to solution

in4ni wrote:



Here is my config and thank you for you taking the time




!
interface pri 1
  description pri 1
  isdn name-delivery setup
  connect t1 0/4 tdm-group 1
  digits-transferred 7
  role network b-channel-restarts disable
  no shutdown


On one (but not both) of the units modify PRI 1 as follows:

interface pri 1

  ....

  role user

  no shutdown


This will be the one acting like PBX.  The other will be acting like a carrier but it really doesn't matter.

Also on one of the units enter:

timing-source internal

(this is default and won't show in the configuration)

On the other enter

timing-source T1 0/4

It doesn't matter which one is which.

You've got digits-transferred 7 but you've got 3-digit extensions.  This might cause some dialplan issues. Try digits-transferred 3 or configure your users with 7-digit numbers.  ISDN and voice debugs will help once you get the units up and in sync.

By the way, good for you!  A lab environment is the place to test and learn, not a customer's phone closet with your cell battery about do die while on hold to Adtran support.

0 Kudos
Anonymous
Not applicable

Re: Using TA908 as a PRI tester

Jump to solution

Add in Role user on one of the units did the trick, D channel came up!  Again Thank you

I have my fist full IP PBX install coming up and the customer has an existing PRI so im trying to get a little fimaliar with the 908 as that is going to be my gateway of choce

When the PBX arrives im going to try to get a PRI to SIP setup going, and test it wuth my second 908.

Thank you very much