cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
hap
New Contributor

Need help configuring a NetVanta 3200 Gen1 for IP pass-thru

Jump to solution

NetVanta 3200 Gen1 w/T1 interface. Firmware version: 15.12.00

I probably have the terminology wrong, but here is what I'm trying to accomplish:

I have a new firewall appliance that I now want to do all the routing for my LAN and I'm struggling with figuring out how to do this. I'm not a network engineer unfortunately.  I have four static IPs assigned to the NetVanta's WAN interface x.x.x.169/170/171/172.

The first thing I believe I should do is to disable the IP routing on the NetVanta. Then I assume I have to populate the default gateway (what gateway? LAN or WAN?). Do I reassign the static IP addresses to the WAN interface on the firewall? That doesn't really make sense to me because the NetVanta still needs an addressable IP address.

Any help or guidance would be much appreciated.

Labels (2)
0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: Need help configuring a NetVanta 3200 Gen1 for IP pass-thru

Jump to solution

- Thanks for posting your question on the forum!

I just want to clarify that based on the firmware you mentioned, it is actually a 2nd Gen 3200. This means you have the ability to use the web interface to configure this device where in the 1st Gen 3200, this option is not available.

You have 3 options to configure this as a pass through:

1. . The easiest option may be just to configure IP unnumbered on the WAN interface. In this option, you would assign on of your usable IP addresses to the ETH 0/1 interface of the NetVanta. Then, under the IP Settings of the WAN interface, you would specify "IP unnumbered" and select the ETH 0/1 interface. The rest of the IP addresses can be used by the firewall with its gateway pointing to the NetVanta.

2. You can request that your T1 provider give you a WAN serial IP address in addition to the LAN block you already have. You would assign the serial IP to the WAN interface of the NetVanta and assign one of the LAN IPs to the ETH 0/1 interface. The rest of the LAN IPs can be used by the firewall which will point to the NetVanta ETH 0/1 IP as its default gateway.

3. You can split the LAN block you already have into smaller subnets. However, you will lose usable IP addresses in doing this. You would assign one half of the subnet to the WAN and the other half to the LAN interface of the NetVanta.

You may find the following document helpful. It does not match your application completely, but it will help in configuring the WAN portion if you have not already done so: Configuring T1 and E1 Internet Access in AOS

Please do not hesitate to let us know if you have any further questions.

Thanks,

Noor

View solution in original post

0 Kudos
1 Reply
Anonymous
Not applicable

Re: Need help configuring a NetVanta 3200 Gen1 for IP pass-thru

Jump to solution

- Thanks for posting your question on the forum!

I just want to clarify that based on the firmware you mentioned, it is actually a 2nd Gen 3200. This means you have the ability to use the web interface to configure this device where in the 1st Gen 3200, this option is not available.

You have 3 options to configure this as a pass through:

1. . The easiest option may be just to configure IP unnumbered on the WAN interface. In this option, you would assign on of your usable IP addresses to the ETH 0/1 interface of the NetVanta. Then, under the IP Settings of the WAN interface, you would specify "IP unnumbered" and select the ETH 0/1 interface. The rest of the IP addresses can be used by the firewall with its gateway pointing to the NetVanta.

2. You can request that your T1 provider give you a WAN serial IP address in addition to the LAN block you already have. You would assign the serial IP to the WAN interface of the NetVanta and assign one of the LAN IPs to the ETH 0/1 interface. The rest of the LAN IPs can be used by the firewall which will point to the NetVanta ETH 0/1 IP as its default gateway.

3. You can split the LAN block you already have into smaller subnets. However, you will lose usable IP addresses in doing this. You would assign one half of the subnet to the WAN and the other half to the LAN interface of the NetVanta.

You may find the following document helpful. It does not match your application completely, but it will help in configuring the WAN portion if you have not already done so: Configuring T1 and E1 Internet Access in AOS

Please do not hesitate to let us know if you have any further questions.

Thanks,

Noor

0 Kudos