cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Anonymous
Not applicable

TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Has anyone had any issues with 10.5.0 not displaying caller-id in call quality stats, nor is it sending it to the PBX.  I did not have this issue with 10.3.1 on the 7100.  Scenario is this Carrier interface is SIP, customer side is PRI.  Sip Stack shows caller-id information in the from field and in the Call-Id context has the gui-id listed.  I ran through the release notes on 10.5.0 and did not see anything indicating change to the display of caller-id.

Thanks in advance for any insight.

John Wable

0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Jwable,

After looking through the complete debug output, we were able to determine that we needed to remove the "p-asserted-identity-required" option from the trust-domain command.  Below is how we made this change.

voice trunk T02 type sip

  no trust-domain p-asserted-identity-required

  trust-domain

Since the unit was not receiving P-asserted-identity, it was not trusting or forwarding the CID that was being received. 

Thanks!

David

View solution in original post

0 Kudos
15 Replies
Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Run "debug isdn l2-formatted" and see if the caller id info is being sent on the PRI.

It's possible the "isdn name-delivery" will need to be changed on the PRI interface.

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution


Here is the output of the Debug, from what I am seeing the Presentation is being screened somewhere alogn the way.  But my provider is just saying that since it is in the From Header it's not them.  Any guidance on where to let them know where to look or what I might need to do differently is much appreciated.

Debug Results:

24 ISDN.L2_FMT PRI  1     IE - 1C FACILITY            Len=14

09:53:04.925 ISDN.L2_FMT PRI  1      Calling Name: not available

09:53:04.925 ISDN.L2_FMT PRI  1     IE - 6C CALLING PARTY #     Len=2

09:53:04.925 ISDN.L2_FMT PRI  1          00 Numb. Type:UNKNOWN      

09:53:04.926 ISDN.L2_FMT PRI  1             Numb. Plan:UNKNOWN       

09:53:04.926 ISDN.L2_FMT PRI  1          C3 Presentation:UNAVAILABLE

09:53:04.926 ISDN.L2_FMT PRI  1             Screening:NTWK PROVIDED

09:53:04.926 ISDN.L2_FMT PRI  1             Ph.#

09:53:04.927 ISDN.L2_FMT PRI  1     IE - 70 CALLED PARTY #      Len=8

09:53:04.927 ISDN.L2_FMT PRI  1          80 Numb. Type:UNKNOWN      

09:53:04.927 ISDN.L2_FMT PRI  1             Numb. Plan:UNKNOWN

INT PRI 1 Config Verbose:

interface pri 1

  description

  alias

  isdn switch-type ni2

  isdn name-delivery setup

  isdn ringing-signal suppress

  no calling-party override

  calling-party presentation allowed

  calling-party screening auto

  no area-code

  no calling-party number

  calling-party name-facility-timeout 2

  connect t1 0/2 tdm-group 1

  digits-transferred 7 no-prefix

  redirecting-number as-received

  role network b-channel-restarts disable

  no isdn alert disable pi-8

  no isdn connect enable pi-2

  no isdn setup enable pi-1

  no isdn setup enable pi-3

  isdn setup enable redirecting-number

  isdn pi-location public

  no isdn supplementary-service tbct

  no isdn supplementary-service tbct notify-controller

  no isdn supplementary-service tbct transfer-counters

  isdn supplementary-service tbct active-transfers 100

  isdn supplementary-service tbct transfer-rate 10

  isdn supplementary-service tbct d-channel-id auto

  snmp trap link-status

  no shutdown

John Wable

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Please send the output from “debug sip stack messages” as well.

This will show what the provider is sending.

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

I have scrubbed vital content prior to posting  Let me know if you need more:

17:45:37.218 SIP.STACK MSG         INVITE sip:803NXXXXXX@xx.xxx.xx.xx:5060;transport=UDP SIP/2.0

17:45:37.218 SIP.STACK MSG         Via: SIP/2.0/UDP xx.xxx.xx.xx:5060;branch=z9hG4bK5brkfk20b0a1mkcb43o0.1

17:45:37.219 SIP.STACK MSG         From: "XXX Comm XXX"<sip:706NXX1234@xx.xxx.xx.xx;user=phone>;tag=SDjdpff01-482818994-1356648305356-

17:45:37.219 SIP.STACK MSG         To: "803NXXXXXX 803NXXXXXX"<sip:803NXXXXXX@voip.net;user=phone>

17:45:37.220 SIP.STACK MSG         Call-ID: SDjdpff01-51d4feb763029f715a64dbee799ebef3-06a53o3

17:45:37.220 SIP.STACK MSG         CSeq: 793061735 INVITE

17:45:37.221 SIP.STACK MSG         Contact: <sip:706NXX1234@xx.xxx.xx.xx:5060;transport=udp>

17:45:37.222 SIP.STACK MSG         Supported: 100rel

17:45:37.223 SIP.STACK MSG         Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE

17:45:37.223 SIP.STACK MSG         Accept: application/media_control+xml,application/sdp,multipart/mixed

17:45:37.224 SIP.STACK MSG         Max-Forwards: 9

17:45:37.225 SIP.STACK MSG         Content-Type: application/sdp

17:45:37.225 SIP.STACK MSG         Content-Length: 255

17:45:37.226 SIP.STACK MSG    

17:45:37.227 SIP.STACK MSG         v=0

17:45:37.227 SIP.STACK MSG         o=BroadWorks 2207701 1 IN IP4 xx.xxx.xx.xx

17:45:37.228 SIP.STACK MSG         s=-

17:45:37.228 SIP.STACK MSG         c=IN IP4 xx.xxx.xx.xx

17:45:37.229 SIP.STACK MSG         t=0 0

17:45:37.229 SIP.STACK MSG         a=sendrecv

17:45:37.230 SIP.STACK MSG         m=audio 63376 RTP/AVP 0 101

17:45:37.230 SIP.STACK MSG         a=rtpmap:0 PCMU/8000

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

The provider is sending caller id name.

Try changing isdn name-delivery to display, proceeding, or setup

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

All three say presentation unavailable, screening network.  This did not happen on code previous to R10.5 with this provider, however because I needed to put in custom tagging I had to use the HMR rules to modify the P-Asserted Identity headers changing the user number to a trunk number so it is also the first time we have deployed using the R10.5 code.  However this is also a brand new config for this provider they are providing the service using a type of trunk group they have not previously used. I went through the release notes and did see an issue where if the caller-id info was being sent as E.164 there was an issue but it also had a work around of setting the international setting to abbreviated which I tried with no change.

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Jwable,

Thanks for posting.  This may be an issue we need to work through a regular Technical Support ticket.  Please call us at 888-423-8726 to open a ticket.  We will likely need to see your complete configuration and the following debug commands, all run at the same time, for a given test call.

debug sip stack message

debug voice verbose

debug hmr

debug isdn L2-formatted

Once we have found the problem, we can post it on the forum.

Thanks!

David

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

David,

    THanks for the reply.  I have tested with version 10.3.1 on a different device connected to a standard trunk with the provider, and it works.  I am in the process of updating to R10.5.0 on the test device to see if it breaks, if it does I know it is related to the 10.5 code, if it doesnt then I know it's related to the new configuration of the provider port.  If it fails when upgrading the code to 10.5 then I will collect all the logs you have stated and open a case, however this is turning into a major issue for the customer so if it work on 10.3 but not 10.5 I will down grade thier code after collecting the logs.

John Wable

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

I have tested the Caller-ID on a test system running the Netvanta 7100 10.5 code and caller ID displays normally.  There is however one major difference between the test and the deployed system and that is the test system is doing SIP to SIP where the deployed system is doing SIP to TDM.

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Jwable,

After looking through the complete debug output, we were able to determine that we needed to remove the "p-asserted-identity-required" option from the trust-domain command.  Below is how we made this change.

voice trunk T02 type sip

  no trust-domain p-asserted-identity-required

  trust-domain

Since the unit was not receiving P-asserted-identity, it was not trusting or forwarding the CID that was being received. 

Thanks!

David

0 Kudos
Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Now that we have caller ID displaying the customer is requesting we reverse the name and number.  They want the number displayed first then the name.  Is that something we can change from the Adtran unit?

John Wable

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

I believe that’s set in the PBX.

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

With AT&T connections the display was number first then name, since changing providers now it is name and then number, no changes made to the PBX in that regard.

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Answer for this was to set no caller-id name-delivery on the Adtran devices.  This way only the number was displayed.  Prior to setting it no delivery I tried all three options, proceeding, setup, and display in all three cases Name was displayed first then number.

conf t

int pri 1

no isdn name-delivery (current setting)

end

wr mem

John Wable

Anonymous
Not applicable

Re: TA 904 10.5.0 Inbound Caller-ID not displayed

Jump to solution

Is there a similar set up for individual voice users SIP/MGCP delivery?