cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
rdawson_atg
New Contributor

Is there a way to monitor the connected status of FXS ports?

Jump to solution

I am trying to find out if there is a way to determine whether an on-hook phone is connected to an FXS port?

Labels (1)
0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

go into the fxs interface and issue "test line"

see below for sample output. I have phone hooked up to 0/2 and no phone on 0/3. You see that 2 passed and 3 failed for the RInger test. And you can compare other results also.

Tiger(config-fxs 0/2)#test line

2018.09.20 12:39:41 FXS.0/2 Initiating Test.

2018.09.20 12:39:41 FXS.0/2 Line Test in progress...

Tiger(config-fxs 0/2)#

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:50 FXS.0/2   HPT            Pass             Loop Impedance

2018.09.20 12:39:50 FXS.0/2   FEMF           Pass             Tip-Ring       8934956.00 Ohms

2018.09.20 12:39:50 FXS.0/2   RFT            Pass             Tip-Ground     5305863.50 Ohms

2018.09.20 12:39:50 FXS.0/2   Ringer         Pass             Ring-Ground    100000000.00 Ohms

2018.09.20 12:39:50 FXS.0/2   ROH            Pass             REN               0.87 REN

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:50 FXS.0/2   Foreign Voltage

2018.09.20 12:39:50 FXS.0/2   Tip-Ground  (ac)    0.00 Volts

2018.09.20 12:39:50 FXS.0/2   Ring-Ground (ac)    0.00 Volts

2018.09.20 12:39:50 FXS.0/2   Tip-Ground  (dc)    0.22 Volts

2018.09.20 12:39:50 FXS.0/2   Ring-Ground (dc)   -0.04 Volts

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:52 FXS.0/2 Restoring service state.

2018.09.20 12:39:52 FXS.0/2 Test complete.

Tiger(config-fxs 0/2)#int fxs 0/3

Tiger(config-fxs 0/3)#test line

2018.09.20 12:40:03 FXS.0/3 Initiating Test.

2018.09.20 12:40:03 FXS.0/3 Line Test in progress...

Tiger(config-fxs 0/3)#

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:11 FXS.0/3   HPT            Pass             Loop Impedance

2018.09.20 12:40:11 FXS.0/3   FEMF           Pass             Tip-Ring       26026618.00 Ohms

2018.09.20 12:40:11 FXS.0/3   RFT            Pass             Tip-Ground     5210722.00 Ohms

2018.09.20 12:40:11 FXS.0/3   Ringer         Fail             Ring-Ground    8447744.00 Ohms

2018.09.20 12:40:11 FXS.0/3   ROH            Pass             REN               0.00 REN

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:11 FXS.0/3   Foreign Voltage

2018.09.20 12:40:11 FXS.0/3   Tip-Ground  (ac)    0.00 Volts

2018.09.20 12:40:11 FXS.0/3   Ring-Ground (ac)    0.00 Volts

2018.09.20 12:40:11 FXS.0/3   Tip-Ground  (dc)    0.13 Volts

2018.09.20 12:40:11 FXS.0/3   Ring-Ground (dc)    0.11 Volts

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:13 FXS.0/3 Restoring service state.

2018.09.20 12:40:13 FXS.0/3 Test complete.

Tiger(config-fxs 0/3)#

View solution in original post

0 Kudos
7 Replies
Anonymous
Not applicable

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

go into the fxs interface and issue "test line"

see below for sample output. I have phone hooked up to 0/2 and no phone on 0/3. You see that 2 passed and 3 failed for the RInger test. And you can compare other results also.

Tiger(config-fxs 0/2)#test line

2018.09.20 12:39:41 FXS.0/2 Initiating Test.

2018.09.20 12:39:41 FXS.0/2 Line Test in progress...

Tiger(config-fxs 0/2)#

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:50 FXS.0/2   HPT            Pass             Loop Impedance

2018.09.20 12:39:50 FXS.0/2   FEMF           Pass             Tip-Ring       8934956.00 Ohms

2018.09.20 12:39:50 FXS.0/2   RFT            Pass             Tip-Ground     5305863.50 Ohms

2018.09.20 12:39:50 FXS.0/2   Ringer         Pass             Ring-Ground    100000000.00 Ohms

2018.09.20 12:39:50 FXS.0/2   ROH            Pass             REN               0.87 REN

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:50 FXS.0/2   Foreign Voltage

2018.09.20 12:39:50 FXS.0/2   Tip-Ground  (ac)    0.00 Volts

2018.09.20 12:39:50 FXS.0/2   Ring-Ground (ac)    0.00 Volts

2018.09.20 12:39:50 FXS.0/2   Tip-Ground  (dc)    0.22 Volts

2018.09.20 12:39:50 FXS.0/2   Ring-Ground (dc)   -0.04 Volts

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:50 FXS.0/2

2018.09.20 12:39:52 FXS.0/2 Restoring service state.

2018.09.20 12:39:52 FXS.0/2 Test complete.

Tiger(config-fxs 0/2)#int fxs 0/3

Tiger(config-fxs 0/3)#test line

2018.09.20 12:40:03 FXS.0/3 Initiating Test.

2018.09.20 12:40:03 FXS.0/3 Line Test in progress...

Tiger(config-fxs 0/3)#

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:11 FXS.0/3   HPT            Pass             Loop Impedance

2018.09.20 12:40:11 FXS.0/3   FEMF           Pass             Tip-Ring       26026618.00 Ohms

2018.09.20 12:40:11 FXS.0/3   RFT            Pass             Tip-Ground     5210722.00 Ohms

2018.09.20 12:40:11 FXS.0/3   Ringer         Fail             Ring-Ground    8447744.00 Ohms

2018.09.20 12:40:11 FXS.0/3   ROH            Pass             REN               0.00 REN

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:11 FXS.0/3   Foreign Voltage

2018.09.20 12:40:11 FXS.0/3   Tip-Ground  (ac)    0.00 Volts

2018.09.20 12:40:11 FXS.0/3   Ring-Ground (ac)    0.00 Volts

2018.09.20 12:40:11 FXS.0/3   Tip-Ground  (dc)    0.13 Volts

2018.09.20 12:40:11 FXS.0/3   Ring-Ground (dc)    0.11 Volts

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:11 FXS.0/3

2018.09.20 12:40:13 FXS.0/3 Restoring service state.

2018.09.20 12:40:13 FXS.0/3 Test complete.

Tiger(config-fxs 0/3)#

0 Kudos

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

Very nice! Do you know when that command was added? Not seeing it on an older software rev.

Thanks,

Rob

Anonymous
Not applicable

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

based on command reference guide, it has been there a very long time, since Release A4.01

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

OK - I'll have to hunt around a bit - getting this on 11.10.1 -

CE-A908-GlobalAuto(config-fxs 0/7)#test

battery                - Provide Battery on 2-wire interface

reverse-battery        - Reverse Battery on 2-wire interface

ringing                - Set 2-wire interface to Ringing

tip-open               - Set 2-wire interface to Tip-Open

tone                   - Enable 1kHz test tone

CE-A908-GlobalAuto(config-fxs 0/7)#test line

% Unrecognized command

Anonymous
Not applicable

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

hmm,

Looks like you might have a 2nd gen TA 900e.

I was on a 3rd gen. I went into a 2nd gen and it didn't have the test line command either.

Not sure of another way to test remotely. You can do test ringing but someone would have to be there to hear phone ringing.

-Mark

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

Yes, 2nd gen . . . guess that gives a good reason to upgrade, at least for this application.

Re: Is there a way to monitor the connected status of FXS ports?

Jump to solution

Thanks again for the quick reply!