cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
bbb
New Contributor II

Atlas 550 not passing CID NAM even though it is in Call Setup message

Jump to solution

The Atlas 550 is not passing CID NAM even though it is in the Call Setup message; it seems to work for less than 24 hours and then stop.

Here is a formatted dump (from the 550) that shows the Name is in the display:

This is what comes from the telco:

07/31 22:05:41             Ph.# 3523333599            
07/31 22:05:41             Numb. Plan:ISDN/Telephony  
07/31 22:05:41          A1 Numb. Type:NATIONAL        
07/31 22:05:41     IE - 70 CALLED PARTY #  Len=11 
07/31 22:05:41             Ph.# 3523310424            
07/31 22:05:41          83 Presentation:ALLOWED       
07/31 22:05:41             Numb. Plan:ISDN/Telephony  
07/31 22:05:41          21 Numb. Type:NATIONAL        
07/31 22:05:41     IE - 6C CALLING PARTY # Len=12 
07/31 22:05:41    53                                  
07/31 22:05:41       B1 46 4C 4F 52 49 44 41 20 50 48 4F 4E
07/31 22:05:41     IE - 28 DISPLAY         Len=16 
07/31 22:05:41          83 Description:ORIG. NOT ISDN 
07/31 22:05:41          80 Location:U                 
07/31 22:05:41     IE - 1E PROGRESS INDICATOR  Len=2  
07/31 22:05:41    CE 15 00 04 0A 01 00                
07/31 22:05:41       9F 8B 01 00 A1 10 02 02 00 E5 06 07 2A
07/31 22:05:41     IE - 1C FACILITY        Len=22 
07/31 22:05:41          81 Channel:1                  
07/31 22:05:41          83 Numb/Map:NUMBER            
07/31 22:05:41             Chan. Sel:FOLLOWS          
07/31 22:05:41             D-Chan Indicated:NO        
07/31 22:05:41             Pref/Excl:EXCLUSIVE        
07/31 22:05:41             Intfc ID:IMPLICIT          
07/31 22:05:41          A9 Primary Rate               
07/31 22:05:41     IE - 18 CHANNEL ID      Len=3  
07/31 22:05:41          A2 Layer 1:u-Law              
07/31 22:05:41          90 Xfer Rate:64k              
07/31 22:05:41          80 Xfer Cap.:SPEECH           
07/31 22:05:41     IE - 04 BEARER CAPABILITY   Len=3  
07/31 22:05:41    M - 05 SETUP                        
07/31 22:05:41    Prot:08  CRL:2  CRV:0073            
07/31 22:05:41    Ctl:INFO Ns:95   Nr:40          

07/31 22:05:41 Recd = Sapi:00  C/R:C Tei:00

However,  this is what the atlas is sending to the KSU:

07/31 22:05:41             Ph.# 3523333599            
07/31 22:05:41             Numb. Plan:UNKNOWN         
07/31 22:05:41          80 Numb. Type:UNKNOWN         
07/31 22:05:41     IE - 70 CALLED PARTY #  Len=11 
07/31 22:05:41             Ph.# 3523310424            
07/31 22:05:41          83 Presentation:ALLOWED       
07/31 22:05:41             Numb. Plan:UNKNOWN         
07/31 22:05:41          00 Numb. Type:UNKNOWN         
07/31 22:05:41     IE - 6C CALLING PARTY # Len=12 
07/31 22:05:41    CE 15 00 04 0A 01 00                
07/31 22:05:41       9F 8B 01 00 A1 10 02 02 00 E5 06 07 2A
07/31 22:05:41     IE - 1C FACILITY        Len=22 
07/31 22:05:41          86 Channel:6                  
07/31 22:05:41          83 Numb/Map:NUMBER            
07/31 22:05:41             Chan. Sel:FOLLOWS          
07/31 22:05:41             D-Chan Indicated:NO        
07/31 22:05:41             Pref/Excl:PREFERRED        
07/31 22:05:41             Intfc ID:IMPLICIT          
07/31 22:05:41          A1 Primary Rate               
07/31 22:05:41     IE - 18 CHANNEL ID      Len=3  
07/31 22:05:41          A2 Layer 1:u-Law              
07/31 22:05:41          90 Xfer Rate:64k              
07/31 22:05:41          80 Xfer Cap.:SPEECH           
07/31 22:05:41     IE - 04 BEARER CAPABILITY   Len=3  
07/31 22:05:41    M - 05 SETUP                        
07/31 22:05:41    Prot:08  CRL:2  CRV:009A            
07/31 22:05:41    Ctl:INFO Ns:10   Nr:10          

07/31 22:05:41 Sent = Sapi:00  C/R:C Tei:00

Any ideas?

0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: Atlas 550 not passing CID NAM even though it is in Call Setup message

Jump to solution

There may be a little confusion. The name does not have to be in a separate facility IE, but it cannot be a DISPLAY IE. The ATLAS 550 supports the name either in the SETUP message or in a supplemental STATUS message, but it does have to be a FACILITY IE. The ATLAS 830 and 890 work best if the name is presented in the SETUP message (as a Facility IE).

View solution in original post

0 Kudos
4 Replies
Anonymous
Not applicable

Re: Atlas 550 not passing CID NAM even though it is in Call Setup message

Jump to solution

Hi bbb,

I don't see the Caller ID Name in the trace from the telco.

Anonymous
Not applicable

Re: Atlas 550 not passing CID NAM even though it is in Call Setup message

Jump to solution

It appears the Caller ID information is being presented as a Display Information Element (IE) as "IE - 28 DISPLAY" followed by the caller ID information. The ATLAS only supports Caller ID in a Facility IE. If the CID Name is not presented as a Facility IE, the ATLAS will not pass the information.

Thank you,

Patrick

bbb
New Contributor II

Re: Atlas 550 not passing CID NAM even though it is in Call Setup message

Jump to solution

Patrick,

  This has not been my experience with the 550.  I see you work with Adtran 🙂  I'm pretty sure that I have called and spoken about this issue with Adtran TS several times, and the name has to be in the setup message, not a separate facility message.  This is not the entire dump, but it is currently being sent in both the setup and a follow up facility message.

  And, oddly enough, it works for about the first 24 hours or so.  Would you please re-confirm that the Atlas expects it as a separate facility (IE 1C) message?

  Thank you!

Anonymous
Not applicable

Re: Atlas 550 not passing CID NAM even though it is in Call Setup message

Jump to solution

There may be a little confusion. The name does not have to be in a separate facility IE, but it cannot be a DISPLAY IE. The ATLAS 550 supports the name either in the SETUP message or in a supplemental STATUS message, but it does have to be a FACILITY IE. The ATLAS 830 and 890 work best if the name is presented in the SETUP message (as a Facility IE).

0 Kudos