17 Replies Latest reply on Sep 22, 2014 11:33 AM by philipl

    CALIX ONT to Adtran 908

    valunet5 New Member


      Anyone out there running the adtran 900's off of Ethernet to CALIX ONT's , to E7-20 to a Metaswitch?

      Our PRI is not getting past the INVITE.

        • Re: CALIX ONT to Adtran 908
          unified Past_Featured_Member

          Hi,

           

          It should work.

          Please send the output of:

          debug sip stack messages

          debug isdn l2-formatted

           

          Thank you,

            • Re: CALIX ONT to Adtran 908
              valunet5 New Member

              123

                • Re: CALIX ONT to Adtran 908
                  unified Past_Featured_Member

                  It looks like the Adtran is trying to register and receiving a "SIP/2.0 501 Not Implemented".

                  Does the Meta require registration?

                   

                  Also I don't see an INVITE the logs above.

                    • Re: CALIX ONT to Adtran 908
                      valunet5 New Member

                      Yes it does.

                       

                      We have an analog line that works fine.

                       

                      Thanks

                      • Re: CALIX ONT to Adtran 908
                        valunet5 New Member

                        123

                          • Re: CALIX ONT to Adtran 908
                            unified Past_Featured_Member

                            If the FXS port is working fine then can you post both the PRI and FXS config.

                              • Re: CALIX ONT to Adtran 908
                                valunet5 New Member

                                123

                                  • Re: CALIX ONT to Adtran 908
                                    unified Past_Featured_Member

                                    Also please post the debug logs during a call from the PRI and FXS.

                                    These may be long, if you are using putty under "Session" you will see "Logging". Here there will be an option to save all output to a file.

                                     

                                    You should remove all private information such as passwords and IP addresses from the post above.

                                    • Re: CALIX ONT to Adtran 908
                                      david.sanchez New Member

                                      Yes, you should remove all private info.  As far as your config:

                                       

                                      1. I have a Metaswitch and I set it up both ways, with or without registration.  It depends on the customer.   I suspect you don't need to register because I see an option message received and you are getting a 501 response to the registration.  That said try removing the the following entries from your sip trunk:

                                       

                                         registrar primary ms.valu-net.net

                                         outbound-proxy primary 199.188.56.130

                                       

                                      Make this change and just send an invite. If it fails, I would try to get the carrier to assist

                                       

                                      2. I also noticed that your PRI interface is on T1 0/2.   I'm not sure if your TA-908e differs from ours, but on our box PRI/CAS trunks can only be on ports 3 & 4

                                        • Re: CALIX ONT to Adtran 908
                                          valunet5 New Member

                                          David.

                                           

                                           

                                           

                                          Do you know what settings and values set up the talk path?

                                           

                                          We have 4 digits passing thru the PRI to our test PBX but no talk path?

                                            • Re: CALIX ONT to Adtran 908
                                              david.sanchez New Member

                                              I believe its the " media-gateway ip primary" setting under the eth interface.  Your settings look correct.  You could try using the "debug sip stack message" command in the TA-098e or a packet capture of the WAN interface to verify the SDP packets.  At that point you would verify the source and destination addresses for RTP.   If you haven't already checked the PRI side, you can use the "debug isdn l2-formatted" command to verify the B-channel and/or monitor using a PRI test set.

                                              • Re: CALIX ONT to Adtran 908
                                                david.sanchez New Member

                                                FYI - I set my SIP trunk to Meta with "accept $ cost 200"

                                                • Re: CALIX ONT to Adtran 908
                                                  geo Employee

                                                  Hello and thank you for posting to our forum.

                                                   

                                                  I want to make sure where you are at in your troubleshooting since there are quite a few posts on this thread.  Please correct me if I am wrong:

                                                   

                                                  You can make a SIP to PRI call and it connects but you get no audio.  If no audio, is it in one or both directions?

                                                   

                                                  If this is correct, here are a couple common problems.  We can look at the possibilities and come up with a plan after:

                                                   

                                                  1.  There is a device in front of the ADTRAN doing NAT and it is not correctly handling the SIP and RTP ports.

                                                  2.  The RTP is not being sent to the correct destination on one or both sides.

                                                   

                                                  In the case for #1, check to see if the router NATing is SIP aware and is able to properly NAT SIP messages, not just the layer 3 source and destination.

                                                   

                                                  In the case for #2, we would like to see a debug of a call, which you would capture the output and either attach it to your response (I would suggest removing any sensitive info) or create a support ticket with us via phone or email.  I would run these debugs:

                                                   

                                                  debug sip stack message

                                                  debug voice verbose

                                                  debug isdn l2-for

                                                   

                                                  Run all 3 of these debugs from the same session so they output together.  Once the call is up, use the command: "show media sum."  This will show the active calls in the unit.  Find your call and then issue the command: "show media session 0/X.Y"  where X is the DSP and Y is the channel shown for your call in the "show media sum."  After that, stop the debug with the command "undebug all."

                                                   

                                                  Regards,

                                                  Geoff

                                                  1 of 1 people found this helpful
                                                    • Re: CALIX ONT to Adtran 908
                                                      valunet5 New Member

                                                      GEO.

                                                       

                                                       

                                                       

                                                      Yes we are still having problems setting up the call leg. It does the “180 ringing” accepts the call leg, and the then goes to a “clearing”

                                                       

                                                      Instead of “ACK” and call setup.

                                                       

                                                       

                                                       

                                                      Our call goes from a metaswitch to calix gpon network, that delivers 4 ethernet ports and 2 voice ports on the ONT.

                                                       

                                                      The CALIX is just a fiber pipe from our customer to the metaswitch in our CO, I don’t think it is NAT’ing.

                                                       

                                                       

                                                       

                                                      As for the second question you had. Im still trying to understand more about the “destination part” and how to troubleshoot it..

                                                       

                                                       

                                                       

                                                      Thanks for your time on this

                                                        • Re: CALIX ONT to Adtran 908
                                                          geo Employee

                                                          If the ADTRAN is going to clearing it sounds like the call is not completing.  Are you able to get a full debug:

                                                           

                                                          debug sip stack message

                                                          debug voice verbose

                                                          debug isdn l2-for

                                                           

                                                          Let me know if you want to continue this here or make a formal ticket in Tech Support.

                                                           

                                                          Regards,

                                                          Geoff

                                                            • Re: CALIX ONT to Adtran 908
                                                              geo Employee

                                                              Hello,

                                                               

                                                              I went ahead and flagged this post as "Assumed Answered". If any of the responses on this thread assisted you, please mark them as Correct or Helpful as the case may be with the applicable buttons. This will make them visible and help other members of the community find solutions more easily. If you still need assistance, we would be more than happy to continue working with you on this - just let us know in a reply.

                                                               

                                                              Thanks,

                                                              Geoff

                                        • Re: CALIX ONT to Adtran 908
                                          philipl New Member


                                          Make sure your calix ont default voice vlan is not the same vlan as that of the 908. If the vlan is the same the ont will not pass the traffic to the 908. You need to create a separate profile name with the voice vlan and pass it trough to the 908. The other thing you might want to look at is the primary and secondary media gateway. The 908 pri media gateway has to match the switch's pri. media gateway others wise it will not work. I have both a Occam and a calix ont working the 924's voice traffic.