3 Replies Latest reply on Feb 20, 2013 6:48 AM by noor

    Trying to access WEB interface

    fordman New Member


      I am trying to access 2 different NV 3200's that were being used to bridge a T1.  I have the ip addresses and I have tried to access both boxes, but fail.  I was able to access one of the boxes using the RS232 and copied the configusration that's listed below.  I am changing the interface card to a 2X T1 and will be bonding the T1s.  Since I already have 2 working config files from a previous pair that I set up, I want to change the applical settings in the config file and up load them to these boxes.  I have looked for a command to load and save the entire file through commands, but was unsuccessful.  so, I need the Web access so I can load the config files.  What am I missing?"  By the way, I have tried both IP addresses shown in config with no success.

       

      hostname "router_1"
      enable password badger
      !
      ip subnet-zero
      ip classless
      no ip routing
      !
      event-history on
      no logging forwarding
      logging forwarding priority-level info
      no logging email
      logging email priority-level info
      !
      banner motd #

                       ****** Important ******

      Enable and Telnet passwords are configured to "password".
      Please change them immediately.

      The ethernet 0/1 interface is enabled with an address of 10.10.10.1
      Telnet access is also enabled.

       

      #
      !
      ip policy-timeout tcp telnet 14400
      !
      ip firewall check syn-flood
      !
      !
      !
      interface eth 0/1
        bridge-group 1
        bridge-group 1 spanning-disabled
        ip address  192.5.9.101  255.255.255.0
        no ip route-cache
        no shutdown
      !
      !
      interface t1 1/1
        tdm-group 1 timeslots 1-24 speed 64
        no shutdown
      !
      interface ppp 1
        bridge-group 1
        bridge-group 1 spanning-disabled
        ip address  192.5.9.101  255.255.255.0
        no ip route-cache
        mtu 1520
        no shutdown
        cross-connect 1 t1 1/1 1 ppp 1
      !
      !
      !
      !
      no ip n-form agent
      no ip snmp agent
      no ip ftp agent
      !
      !
      !
      bridge 1 protocol ieee
      !
      !
      line con 0
        no login
      !
      line telnet 0 4
        login
        password "badger"
      !
      end

        • Re: Trying to access WEB interface
          eric17 Employee

          fordman – Based off the output from the ‘show version’ that you emailed to us earlier, it appears that you are running 05.02.00 firmware.  I was looking through the release notes, and the web GUI for our 3000 series was added as a feature in code 7.01.00.  In order to enable the GUI, you will need to upgrade to 7.01.00 or higher code.  Once you upgrade, you will type the following, as you previously did over the phone, to enable the web interface:

          Router> en

          Router# config t

          Router(config)# ip http server

           

          Below contains the link to our guide for upgrading firmware in AOS:

           

          https://supportforums.adtran.com/docs/DOC-1672

           

          Please feel free to let us know if you have any more questions or concerns regarding this issue. 

           

          Thanks,

          Eric

          • Re: Trying to access WEB interface
            levi Employee

            fordman:

             

            I went ahead and flagged this post as “Assumed Answered.”  If any of the responses on this thread assisted you, please mark them as either Correct or Helpful answers with the applicable buttons.  This will make them visible and help other members of the community find solutions more easily.  If you still need assistance, I would be more than happy to continue working with you on this - just let me know in a reply.

             

            Levi

              • Re: Trying to access WEB interface
                Employee

                I went ahead and flagged the "Correct Answer" on this post to make it more visible and help other members of the community find solutions more easily. If you don't feel like the answer I marked was correct, feel free to come back to this post and unmark it and select another in its place with the applicable buttons.  If you still need assistance, we would be more than happy to continue working with you on this - just let us know in a reply.

                 

                Thanks,

                Noor