9 Replies Latest reply on Apr 7, 2014 8:15 AM by levi

    Unable to update firmware of NV160 access point

    brianwilliams New Member

      Good afternoon Adtran Support,

       

      I had a remote user connect a NV160 to the network but my NV1335 controller wasn't using the latest firmware to allow configuration of the AP. After installing the controller firmware, I rebooted the device and when I looked at the AP Discovery section, I saw that the NV160 had a status of "Recovery." I set about putting a temporary vlan in place so that I could access the default IP (192.168.190.1 /24) of the AP and upgrade the firmware in accordance to the PDF, "Upgrading Firmware on a Netvanta 160." After I had gotten the network prepared with my temporary vlan and such, I am able to ping 192.168.190.1 just fine. However, the controller no longer sees the access point, so I'm unable to upgrade the firmware through the controller. I discovered this when I tried to push the firmware and I got the error "...no session exists..." That's when I looked at Wireless -> AC/AP Discovery on the controller to see that it was no longer showing up.

       

      I have restarted the controller as well as disabled/re-enabled the port that the AP is plugged into, but I'm unable to get the controller to 'discover' the AP again. I also attempted to just manually add the AP via MAC address & IP - but no luck with that, I received the same "no session exists" error.  Could someone offer any insight as to how I can get this AP to show back up? I think it's the only way that I can push the necessary firmware to the AP to get it out of the 'recovery' mode.

       

      Thanks!

       

      Brian

        • Re: Unable to update firmware of NV160 access point
          Employee

          brianwilliams - Can you post the Access Controller configuration you are using when attempting to upgrade the firmware on the NetVanta 160? Also, which switchport is the NetVanta 160 plugging into? Please remember to remove any sensitive information.

           

          Thanks,

          Noor

            • Re: Unable to update firmware of NV160 access point
              brianwilliams New Member

              Sure, let me grab the config and sanitize it. I'm not plugging the AP into the controller itself, I have it plugged into a PoE switch on the network. I had to go through and create the test vlan for the default IP of the AP (192.168.190.1 /24) and I can still ping that address from one of my servers (that is being used as my tftp server). The problem that I'm having is that I can't get the controller to 'discover' the AP again so that it has an active session when I'm trying to upgrade the firmware.

               

              Is there a time-out feature where if the AP is in recovery status, the controller will just eventually reject it? I just need to figure out how to 'reset' it so that the controller discovers the AP again long enough for me to update it's firmware. Then I can back out all of the changes to the network I had to make in order to be able to route to 192.168.190.1 /24.

               

              Building configuration...

              !

              !

              ! ADTRAN, Inc. OS version R10.8.0.E

              ! Boot ROM version 15.01.B1

              ! Platform: NetVanta 1335 PoE, part number 1700525E2

              ! Serial number LBADTN1107AA955

              !

              !

              hostname "XXXX"

              !

              clock timezone -5-Eastern-Time

              !

              ip subnet-zero

              ip classless

              ip default-gateway 10.5.101.10

              ip routing

              !

              !

              !

              !

              no ip route-cache express

              !

              no auto-config

              !

              event-history on

              no logging forwarding

              no logging email

              !

              service password-encryption

              !

              !

               

               

              !

              !

              no ip firewall

              no ip firewall alg msn

              no ip firewall alg mszone

              no ip firewall alg pptp

              no ip firewall alg h323

              !

              !

              !

              !

              !

              !

              !

              !

              dot11ap access-point-control

              !

              !

              !

              !

              !

              !

              ip dhcp database local

              ip dhcp excluded-address 192.168.40.1 192.168.40.49

              !

              ip dhcp pool "Guest"

                network 192.168.40.0 255.255.255.0

                dns-server 8.8.8.8

                netbios-node-type h-node

                default-router 192.168.40.1

              !

              !

              !

              !

              !

              !

              !

              !

              !

              vlan 1

                name "Default"

              !

              vlan 10

                name "Guest_Wireless"

              !

              vlan 190

                name "VLAN0190"

              !

              !

              interface switchport 0/1

                description Connect to NV150-01

                no shutdown

                switchport mode trunk

              !

              interface switchport 0/2

                no shutdown

              !

              interface switchport 0/3

                no shutdown

              !

              interface switchport 0/4

                no shutdown

              !

              interface switchport 0/5

                no shutdown

              !

              interface switchport 0/6

                no shutdown

              !

              interface switchport 0/7

                no shutdown

              !

              interface switchport 0/8

                no shutdown

              !

              interface switchport 0/9

                no shutdown

              !

              interface switchport 0/10

                no shutdown

              !

              interface switchport 0/11

                no shutdown

              !

              interface switchport 0/12

                no shutdown

              !

              interface switchport 0/13

                no shutdown

              !

              interface switchport 0/14

                no shutdown

              !

              interface switchport 0/15

                no shutdown

              !

              interface switchport 0/16

                no shutdown

              !

              interface switchport 0/17

                no shutdown

              !

              interface switchport 0/18

                no shutdown

              !

              interface switchport 0/19

                no shutdown

              !

              interface switchport 0/20

                no shutdown

              !

              interface switchport 0/21

                no shutdown

              !

              interface switchport 0/22

                no shutdown

              !

              interface switchport 0/23

                no shutdown

              !

              interface switchport 0/24

                no shutdown

              !

              !

              interface gigabit-switchport 0/1

                description Uplink to Network

                no shutdown

                switchport mode trunk

                switchport trunk allowed vlan 10,190

              !

              interface gigabit-switchport 0/2

                no shutdown

              !

              !

              !

              interface vlan 1

                ip address  10.5.101.7  255.255.255.0

                ip route-cache express

                no shutdown

              !

              interface vlan 10

                description Guest Wireless

                ip address  192.168.40.1  255.255.255.0

                ip route-cache express

                no shutdown

              !

              interface vlan 190

                no ip address

                ip route-cache express

                shutdown

              !

              !

              interface dot11ap 1 ap-type nv150

                access-point mac-address 00:A0:C8:69:41:B0

                name AP01

                ip address 10.5.101.20 255.255.255.0

                ip default-gateway 10.5.101.9

                encapsulation 802.1q awcp-vlan 1 native priority 7

              !

              !

              interface dot11ap 1/1 radio-type 802.11bg

                no shutdown

              !

              !

              interface dot11ap 1/1.1

                description Wiz_802.11BG_VAP

                ssid nonbroadcast-mode "Internal"

                security mode wpa aes-ccmp psk XXXX

                no shutdown

              !

              interface dot11ap 1/1.2

                description guest wireless

                vlan-id 10

                ssid broadcast-mode "Guest"

                security mode wpa aes-ccmp psk XXXX

                no shutdown

              !

              !

              interface dot11ap 1/2 radio-type 802.11a

                shutdown

              !

              !

              interface dot11ap 1/2.1

                security mode none

                shutdown

              !

              !

              !

              ip route 0.0.0.0 0.0.0.0 10.5.101.10

              ip route 10.150.101.0 255.255.255.0 10.5.101.10

              !

              no tftp server

              no tftp server overwrite

              http server

              http secure-server

              snmp agent

              no ip ftp server

              ip ftp server default-filesystem flash

              no ip scp server

              no ip sntp server

              !

              !

              !

              sip udp 5060

              sip tcp 5060

              !

              !

              !

              sip proxy grammar contact outbound-server-reference host domain

              !

              !

              !

              end

                • Re: Unable to update firmware of NV160 access point
                  Employee

                  brianwilliams - Is your TFTP server on the same switch as the NetVanta 160? As a test, would you be able to enable the VLAN you created for the 160 and give it an IP address in the 192.168.190.x network? I think it is VLAN 190. Once that is done, are you able to ping the VLAN interface IP from the TFTP server? Another test would be to move the 160 so that it is directly connected to the Access Controller and seeing if your TFTP server can still ping it.

                   

                  Thanks,

                  Noor

                  1 of 1 people found this helpful
                    • Re: Unable to update firmware of NV160 access point
                      brianwilliams New Member

                      My TFTP server is indeed on the same switch as the NV160. From the router, switch, controller and TFTP server, I'm able to ping the NV160 with its default IP of 192.168.190.1 /24. I just can't get the controller to 'discover' the AP any longer, thereby not allowing a session to be created which is prohibiting me from installing the firmware. Is there a way I can telnet or SSH into the access point directly by it's default IP? Or do I have have to use the controller to push the firmware?

                       

                      Thanks!

                        • Re: Unable to update firmware of NV160 access point
                          Employee

                          brianwilliams - Yes, you will need to update the firmware using the access controller. This is why I was suggesting the tests in my previous post. This would be to confirm that the switchport settings between the AP/TFTP server switch and the access controller are correct.

                           

                          I'm not sure if you have already looked at this document, but, if not, you may find it helpful: Upgrading Firmware on an ADTRAN Netvanta 160 Series Unit in Recovery Mode

                           

                          Thanks,

                          Noor

                            • Re: Unable to update firmware of NV160 access point
                              brianwilliams New Member

                              Understood. The way that I knew how to configure the switch, router and controller temporarily to allow access to the AP in recovery mode was by reading the document you suggested. From the router, switch and controller, I can ping the 192.168.190.1 address that the AP currently has. But, for some reason, the controller isn't recognizing or discovering the AP as it did before. When I first plugged the AP into the switch, the controller itself had the wrong firmware which I didn't notice until the controller had already discovered the AP. I installed the new firmware on the controller, rebooted and then saw that the AP was in recovery mode. I followed the instructions of the PDF linked above to be able to access the 192.168.190.1 IP address. When I attempted to load the firmware to the AP itself, the controller lost it's session with the AP and now won't initialize or discover the AP.

                               

                              What I'm curious about or require help with is how to get the controller to recognize the AP again in it's discovery process. Without the controller discovering or connecting a session to the AP while in recovery mode, I can't push the AP firmware to get it out of recovery mode. I've attempted restarting the controller, disabling/re-enabling the switchport that the AP is plugged into, but none of those things has worked. I even tried to manually add the AP via MAC address to the controller - but I get the same error that no session exists between controller and AP, because it didn't "discover" it.

                    • Re: Unable to update firmware of NV160 access point
                      levi Employee

                      brianwilliams:

                       

                      I went ahead and flagged this post as "Assumed Answered." If any of the responses on this thread assisted you, please mark them as Correct or Helpful as the case may be with the applicable buttons. This will make them visible and help other members of the community find solutions more easily. If you still need assistance, we would be more than happy to continue working with you on this - just let us know in a reply.

                       

                      Levi