4 Replies Latest reply on May 22, 2014 9:18 AM by nps48

    TA3000 DSLAM with EFM CARD

    apenichet New Member

      I am trying to get an TA832 to work with a TA3000 DSLAM using a SHDSL-16-PORT-EFM card. I think I almost got everything right. I tried to use the same config on the TA832 that I use when deploying out of the TA500. Im going to throw config below. If anyone has any ideas on a specific config for the TA832 going to this specific card. I am using VLAN Trunked all the way through and then as an untagged port on the ethernet port of the TA832.

       

      !Building configuration...

      !

      !

      !Operational Modes - require a reboot to take effect

      !shdsl mode ntu

      !snmp-server ifindex-mode sequential

      !

      ip default-gateway 00.00.00.1

      !

      !

      clock timezone "EASTERN" -5 0

      !

      !

      !

      !

      !

      !

      !

      !

      security

      !

        username ADMIN

          password md5 "0x319F4D26E3C536B5DD871BB2C52E3178"

          privilege admin

      !

        username READONLY

          password md5 "0x319F4D26E3C536B5DD871BB2C52E3178"

          privilege read-only

      !

        username READWRITE

          password md5 "0x319F4D26E3C536B5DD871BB2C52E3178"

          privilege read-write

      !

        username TEST

          password md5 "0x319F4D26E3C536B5DD871BB2C52E3178"

          privilege test

      !

      !

      !

      !

      !

      probe responder twamp

      !      

      !

      qos cos-map 0 0 1

      qos cos-map 1 2 3

      qos cos-map 2 4 5

      qos cos-map 3 6 7

      !

      !

      interface shdsl 1/0/1

        description "SHDSL PORT1"

        linerate adaptive 3-89 0 worstcase-condition

      !

      !

      interface shdsl 1/0/2

        description "SHDSL PORT2"

        linerate adaptive 3-89 0 worstcase-condition

      !

      !

       

       

      !

      !

      interface efm-group 1/0/1

        alias "EFM GROUP 1/0/1"

        s-tag-dei

        link 0/1,0/2

        subtended-host mode listener

        no shutdown

        ethernet evc-advertisement

        ethernet oam enable

      !

      !

      interface efm-link 1/0/1

      !

      !

      interface efm-link 1/0/2

      !

      !

      interface ethernet 1/0/1

        subtended-host mode disabled

        ethernet evc-advertisement

        ethernet oam enable

      !

      !

      system-management-evc

        s-tag 3001

        connect men-port efm-group 1/0/1

        ip address 00.00.00.2 255.255.255.248

        no shutdown

      !

      !

      evc "EFM-LAB"

        s-tag 3001

        connect men-port efm-group 1/0/1

        no preserve-ce-vlan

        no shutdown

      !

      !

      evc-map "EFM-LAB"

        connect evc "EFM-LAB"

        men-pri inherit

        connect uni ethernet 1/0/1

        match untagged

        men-c-tag-pri inherit

        no shutdown

      !

      !

      !

      !

      !

      !      

      snmp-server community read-only "lookatit"

      snmp-server chassis-id "CUSTOMER-NAME"

      !

      !

      line console 0

        speed 9600

      !

      !

      !

      !

      !

      !

      !

      !

      !

      end

        • Re: TA3000 DSLAM with EFM CARD
          dsc Employee

          The configuration looks correct except I would not recommend using the same vlan for the system-management-evc and the "EFM-LAB" evc.  It is also recommended you have A01.16 code on the TA3000 SHDSL16 EFM card for this application.

            • Re: TA3000 DSLAM with EFM CARD
              apenichet New Member

              I figured I would have to go back to an older release firmware. Now the good question is where can I find that firmware. The support site does not have any software for that 832 EFM. Its blank when you search on the Adtran page.

                • Re: TA3000 DSLAM with EFM CARD
                  dsc Employee

                  A01.16 is the latest code for the TA3000 SHDSL16 EFM card.  If you have an old TA832 instead of the NetVanta 832 you probably need to disable loopback detect in the efm-group.  No new code has been developed for the old TA832 in years and what you have is probably current.

              • Re: TA3000 DSLAM with EFM CARD
                nps48 Employee

                Hello

                The TA 3000 does not do subtend host command. It is recommended that you not use the same vlan for mgmt and data.

                 

                 

                interface efm-group 1/0/1

                  alias "EFM GROUP 1/0/1"

                  s-tag-dei

                  link 0/1,0/2

                  subtended-host mode listener   config t   

                                                             int efm-group 1/0/1

                                                             no subtended-host mode

                                                            no  ethernet evc-advertisement

                  no shutdown

                  ethernet evc-advertisement

                  ethernet oam enable

                 

                 

                evc "EFM-LAB"

                  s-tag 3001

                  connect men-port efm-group 1/0/1

                  no preserve-ce-vlan

                  no shutdown

                !

                !

                evc-map "EFM-LAB"

                  connect evc "EFM-LAB"

                  men-pri inherit

                  connect uni ethernet 1/0/1

                  match untagged

                  men-c-tag-pri inherit

                  no shutdown