1 Reply Latest reply on Feb 18, 2015 4:23 PM by mmaner

    Netvanta 1224ST Stuck in #BOOTSTRAP

    mikemunn New Member

      I have a Netvanta 1224ST that was suddenly unpingable.

       

      I consoled in and got a #BOOTSTRAP: prompt. It looks like something went wrong. I try to assign an IP and it started cycling this:

       

      bootstrap#

      Switch (1200504L1)

      Executing bootstrap...

      ram: 16777216 bytes of RAM detected.

      Serial Number: LBADTN0816AA732

      Bootstrap version: 12.02.00, checksum: C440, Fri May 12 15:14:02 2006

      CORE: source\PacketCoreDrivers\IDT3233X\Interrupts.cpp#488: AdFatal(Invalid load or fetch from address = 0x00000027. Access occurred at PC = 0x000c019c, SP = 0x8016d140.  StackTrc: Warning!  Stack ptr = 8016D140 not in CurrentTask's range(00183bd0 - 0018bbd0)

      )..F^..>..~.o...~"

      flash: initializing flash devices...

      flash: 8388608 bytes of FLASH detected at 0xbc000000

      vfs: NONVOL: 120 tracks, 64 sectors/track, 1024 bytes/sector.

      eth0/1: initializing...

      switch: 16 MB of buffer pool DRAM detected, 64 bit bus width

      bootstrap: Checking boot configuration...

      bootstrap: Boot configuration not found.

      bootstrap: Upload a new image using the 'copy' command

                 or specify the correct primary/backup images using the

                 'boot system flash <filename> <backup_filename>' command.

      bootstrap: Error in boot configuration!!!  Checking backup boot configuration.

      bootstrap: Boot configuration not found.

      bootstrap: Invalid boot configuration, entering bootstrap mode...

      cli: starting user interface

        • Re: Netvanta 1224ST Stuck in #BOOTSTRAP
          mmaner New Member

          Follow these directions to reload the firmware of the unit and load a basic startup config.  After this is complete, you should be able to program the unit as desired and place into production.

           

          Download the firmware of your choice for the Adtran Netvanta 1224ST at Software Downloads

          Download Tera Term Pro at TeraTerm 3.1.3 - Telnet, SSH2, SSL Client with built in Web Server

          Connect to the unit with a console cable (9 pin straight-through serial cable)
          Open Tera Term Pro & m
          ake a serial connection to the unit

           

          Type the following...

          erase file-system

            [wait for completion, 100%]

          copy xmodem flash

          [the name of the firmware you downloaded earlier]

          * in Tera Term - file > transfer > xmodem > send > select the firmware you downloaded earlier.

           

          Select the following text and save to a file named starup-config with no extension

           

          !

          !

          hostname "Switch"

          enable password password

          !

          event-history on

          no logging forwarding

          no logging email

          logging email priority-level info

          !

          username "admin" password "password"

          !

          banner motd #

                           ****** Important ******

          Enable and Telnet passwords are configured to "password".

          Please change them immediately.

          The vlan 1 interface is enabled with an address of 10.10.10.1

          Telnet access is also enabled.

           

           

           

           

          #

          !

          !

          !

          !

          !

          !

          !

          !

          !

          vlan 1

            name "Default"

          !

          interface vlan 1

            ip address  10.10.10.1  255.255.255.0

            no shutdown

          !

          !

          !

          no ip tftp server

          ip http server

          no ip http secure-server

          no ip snmp agent

          no ip ftp agent

          !

          !

          !

          !

          !

          !

          !

          line con 0

            no login

          !

          line telnet 0 4

            login

            password password

          !

          !

          !

          !

          !

          end

           

          Go back to Tera Term Pro and type the following...

           

          copy xmodem flash

          startup-config

          * in Tera Term - file > transfer > xmodem > send > select startup-config

          boot