1 Reply Latest reply on Jan 7, 2016 10:24 AM by jayh

    program SIP to T1 cas

    acowles New Member

      I know this is old school but i need to  setup SIP to CAS T1.now it is setup as a SIP to PRI

      on the T! side  i have this already

       

      interface t1 0/2

      framing d4

      coding ami

       

      Can you tell me what else needs to be done

        • Re: program SIP to T1 cas
          jayh Hall_of_Fame
          • Warning, make sure that T1 0/2 is capable of TDM voice. On gen. 1 and 2 e-series TA9xx you need to use T1 3 or 4.
          • If trunk T02 is in use for something else, use a different trunk number.
          • For D4/AMI you will probably need to change speeds below to 56.
          • Set system timing-source appropriately. (Different discussion, write back if unclear)

           

          Config follows:

           

          interface t1 0/2

          tdm-group 1 timeslots 1 speed 64

            tdm-group 2 timeslots 2 speed 64

            tdm-group 3 timeslots 3 speed 64

            tdm-group 4 timeslots 4 speed 64

            tdm-group 5 timeslots 5 speed 64

            tdm-group 6 timeslots 6 speed 64

            tdm-group 7 timeslots 7 speed 64

            tdm-group 8 timeslots 8 speed 64

            tdm-group 9 timeslots 9 speed 64

            tdm-group 10 timeslots 10 speed 64

            tdm-group 11 timeslots 11 speed 64

            tdm-group 12 timeslots 12 speed 64

            tdm-group 13 timeslots 13 speed 64

            tdm-group 14 timeslots 14 speed 64

            tdm-group 15 timeslots 15 speed 64

            tdm-group 16 timeslots 16 speed 64

            tdm-group 17 timeslots 17 speed 64

            tdm-group 18 timeslots 18 speed 64

            tdm-group 19 timeslots 19 speed 64

            tdm-group 20 timeslots 20 speed 64

            tdm-group 21 timeslots 21 speed 64

            tdm-group 22 timeslots 22 speed 64

            tdm-group 23 timeslots 23 speed 64

            tdm-group 24 timeslots 24 speed 64

            no shutdown

           

          voice trunk T02 type t1-rbs supervision wink role network

            description "PBX RBS"

            resource-selection linear ascending [Use opposite direction from PBX to reduce glare]

            caller-id-override number-inbound [Number to present as ANI from trunk]

            caller-id-override emergency-outbound [Number to present as emergency ANI from trunk]

            did digits-transferred 4 [Change to what PBX is configured to take if not 4]

            connect t1 0/2 tdm-group 1

            connect t1 0/2 tdm-group 2

            connect t1 0/2 tdm-group 3

            connect t1 0/2 tdm-group 4

            connect t1 0/2 tdm-group 5

            connect t1 0/2 tdm-group 6

            connect t1 0/2 tdm-group 7

            connect t1 0/2 tdm-group 8

            connect t1 0/2 tdm-group 9

            connect t1 0/2 tdm-group 10

            connect t1 0/2 tdm-group 11

            connect t1 0/2 tdm-group 12

            connect t1 0/2 tdm-group 13

            connect t1 0/2 tdm-group 14

            connect t1 0/2 tdm-group 15

            connect t1 0/2 tdm-group 16

            connect t1 0/2 tdm-group 17

            connect t1 0/2 tdm-group 18

            connect t1 0/2 tdm-group 19

            connect t1 0/2 tdm-group 20

            connect t1 0/2 tdm-group 21

            connect t1 0/2 tdm-group 22

            connect t1 0/2 tdm-group 23

            connect t1 0/2 tdm-group 24

            modem-passthrough

            rtp delay-mode adaptive

          !

          voice grouped-trunk PBX

            trunk T02

            accept [Pattern of incoming numbers to route to PBX]